|
NAME | SYNOPSIS | MATCH EXTENSIONS | TARGET EXTENSIONS | COLOPHON |
|
iptables-extensions(8) iptables 1.6.1 iptables-extensions(8)
iptables-extensions — list of extensions in the standard iptables
distribution
ip6tables [-m name [module-options...]] [-j target-name [target-
options...]
iptables [-m name [module-options...]] [-j target-name [target-
options...]
iptables can use extended packet matching modules with the -m or
--match options, followed by the matching module name; after these,
various extra command line options become available, depending on the
specific module. You can specify multiple extended match modules in
one line, and you can use the -h or --help options after the module
has been specified to receive help specific to that module. The
extended match modules are evaluated in the order they are specified
in the rule.
If the -p or --protocol was specified and if and only if an unknown
option is encountered, iptables will try load a match module of the
same name as the protocol, to try making the option available.
addrtype
This module matches packets based on their address type. Address
types are used within the kernel networking stack and categorize
addresses into various groups. The exact definition of that group
depends on the specific layer three protocol.
The following address types are possible:
UNSPEC an unspecified address (i.e. 0.0.0.0)
UNICAST
an unicast address
LOCAL a local address
BROADCAST
a broadcast address
ANYCAST
an anycast packet
MULTICAST
a multicast address
BLACKHOLE
a blackhole address
UNREACHABLE
an unreachable address
PROHIBIT
a prohibited address
THROW FIXME
NAT FIXME
XRESOLVE
[!] --src-type type
Matches if the source address is of given type
[!] --dst-type type
Matches if the destination address is of given type
--limit-iface-in
The address type checking can be limited to the interface the
packet is coming in. This option is only valid in the
PREROUTING, INPUT and FORWARD chains. It cannot be specified
with the --limit-iface-out option.
--limit-iface-out
The address type checking can be limited to the interface the
packet is going out. This option is only valid in the
POSTROUTING, OUTPUT and FORWARD chains. It cannot be specified
with the --limit-iface-in option.
ah (IPv6-specific)
This module matches the parameters in Authentication header of IPsec
packets.
[!] --ahspi spi[:spi]
Matches SPI.
[!] --ahlen length
Total length of this header in octets.
--ahres
Matches if the reserved field is filled with zero.
ah (IPv4-specific)
This module matches the SPIs in Authentication header of IPsec
packets.
[!] --ahspi spi[:spi]
bpf
Match using Linux Socket Filter. Expects a path to an eBPF object or
a cBPF program in decimal format.
--object-pinned path
Pass a path to a pinned eBPF object.
Applications load eBPF programs into the kernel with the bpf() system
call and BPF_PROG_LOAD command and can pin them in a virtual
filesystem with BPF_OBJ_PIN. To use a pinned object in iptables,
mount the bpf filesystem using
mount -t bpf bpf ${BPF_MOUNT}
then insert the filter in iptables by path:
iptables -A OUTPUT -m bpf --object-pinned
${BPF_MOUNT}/{PINNED_PATH} -j ACCEPT
--bytecode code
Pass the BPF byte code format as generated by the
nfbpf_compile utility.
The code format is similar to the output of the tcpdump -ddd command:
one line that stores the number of instructions, followed by one line
for each instruction. Instruction lines follow the pattern 'u16 u8 u8
u32' in decimal notation. Fields encode the operation, jump offset if
true, jump offset if false and generic multiuse field 'K'. Comments
are not supported.
For example, to read only packets matching 'ip proto 6', insert the
following, without the comments or trailing whitespace:
4 # number of instructions
48 0 0 9 # load byte ip->proto
21 0 1 6 # jump equal IPPROTO_TCP
6 0 0 1 # return pass (non-zero)
6 0 0 0 # return fail (zero)
You can pass this filter to the bpf match with the following command:
iptables -A OUTPUT -m bpf --bytecode '4,48 0 0 9,21 0 1 6,6 0
0 1,6 0 0 0' -j ACCEPT
Or instead, you can invoke the nfbpf_compile utility.
iptables -A OUTPUT -m bpf --bytecode "`nfbpf_compile RAW 'ip
proto 6'`" -j ACCEPT
Or use tcpdump -ddd. In that case, generate BPF targeting a device
with the same data link type as the xtables match. Iptables passes
packets from the network layer up, without mac layer. Select a device
with data link type RAW, such as a tun device:
ip tuntap add tun0 mode tun
ip link set tun0 up
tcpdump -ddd -i tun0 ip proto 6
See tcpdump -L -i $dev for a list of known data link types for a
given device.
You may want to learn more about BPF from FreeBSD's bpf(4) manpage.
cgroup
[!] --path path
Match cgroup2 membership.
Each socket is associated with the v2 cgroup of the creating
process. This matches packets coming from or going to all
sockets in the sub-hierarchy of the specified path. The path
should be relative to the root of the cgroup2 hierarchy.
[!] --cgroup classid
Match cgroup net_cls classid.
classid is the marker set through the cgroup net_cls
controller. This option and --path can't be used together.
Example:
iptables -A OUTPUT -p tcp --sport 80 -m cgroup ! --path
service/http-server -j DROP
iptables -A OUTPUT -p tcp --sport 80 -m cgroup ! --cgroup 1 -j
DROP
IMPORTANT: when being used in the INPUT chain, the cgroup matcher is
currently only of limited functionality, meaning it will only match
on packets that are processed for local sockets through early socket
demuxing. Therefore, general usage on the INPUT chain is not advised
unless the implications are well understood.
Available since Linux 3.14.
cluster
Allows you to deploy gateway and back-end load-sharing clusters
without the need of load-balancers.
This match requires that all the nodes see the same packets. Thus,
the cluster match decides if this node has to handle a packet given
the following options:
--cluster-total-nodes num
Set number of total nodes in cluster.
[!] --cluster-local-node num
Set the local node number ID.
[!] --cluster-local-nodemask mask
Set the local node number ID mask. You can use this option
instead of --cluster-local-node.
--cluster-hash-seed value
Set seed value of the Jenkins hash.
Example:
iptables -A PREROUTING -t mangle -i eth1 -m cluster
--cluster-total-nodes 2 --cluster-local-node 1
--cluster-hash-seed 0xdeadbeef -j MARK --set-mark 0xffff
iptables -A PREROUTING -t mangle -i eth2 -m cluster
--cluster-total-nodes 2 --cluster-local-node 1
--cluster-hash-seed 0xdeadbeef -j MARK --set-mark 0xffff
iptables -A PREROUTING -t mangle -i eth1 -m mark ! --mark
0xffff -j DROP
iptables -A PREROUTING -t mangle -i eth2 -m mark ! --mark
0xffff -j DROP
And the following commands to make all nodes see the same packets:
ip maddr add 01:00:5e:00:01:01 dev eth1
ip maddr add 01:00:5e:00:01:02 dev eth2
arptables -A OUTPUT -o eth1 --h-length 6 -j mangle --mangle-
mac-s 01:00:5e:00:01:01
arptables -A INPUT -i eth1 --h-length 6 --destination-mac
01:00:5e:00:01:01 -j mangle --mangle-mac-d 00:zz:yy:xx:5a:27
arptables -A OUTPUT -o eth2 --h-length 6 -j mangle
--mangle-mac-s 01:00:5e:00:01:02
arptables -A INPUT -i eth2 --h-length 6 --destination-mac
01:00:5e:00:01:02 -j mangle --mangle-mac-d 00:zz:yy:xx:5a:27
NOTE: the arptables commands above use mainstream syntax. If you are
using arptables-jf included in some RedHat, CentOS and Fedora
versions, you will hit syntax errors. Therefore, you'll have to adapt
these to the arptables-jf syntax to get them working.
In the case of TCP connections, pickup facility has to be disabled to
avoid marking TCP ACK packets coming in the reply direction as valid.
echo 0 > /proc/sys/net/netfilter/nf_conntrack_tcp_loose
comment
Allows you to add comments (up to 256 characters) to any rule.
--comment comment
Example:
iptables -A INPUT -i eth1 -m comment --comment "my local LAN"
connbytes
Match by how many bytes or packets a connection (or one of the two
flows constituting the connection) has transferred so far, or by
average bytes per packet.
The counters are 64-bit and are thus not expected to overflow ;)
The primary use is to detect long-lived downloads and mark them to be
scheduled using a lower priority band in traffic control.
The transferred bytes per connection can also be viewed through
`conntrack -L` and accessed via ctnetlink.
NOTE that for connections which have no accounting information, the
match will always return false. The "net.netfilter.nf_conntrack_acct"
sysctl flag controls whether new connections will be byte/packet
counted. Existing connection flows will not be gaining/losing a/the
accounting structure when be sysctl flag is flipped.
[!] --connbytes from[:to]
match packets from a connection whose packets/bytes/average
packet size is more than FROM and less than TO bytes/packets.
if TO is omitted only FROM check is done. "!" is used to match
packets not falling in the range.
--connbytes-dir {original|reply|both}
which packets to consider
--connbytes-mode {packets|bytes|avgpkt}
whether to check the amount of packets, number of bytes
transferred or the average size (in bytes) of all packets
received so far. Note that when "both" is used together with
"avgpkt", and data is going (mainly) only in one direction
(for example HTTP), the average packet size will be about half
of the actual data packets.
Example:
iptables .. -m connbytes --connbytes 10000:100000
--connbytes-dir both --connbytes-mode bytes ...
connlimit
Allows you to restrict the number of parallel connections to a server
per client IP address (or client address block).
--connlimit-upto n
Match if the number of existing connections is below or equal
n.
--connlimit-above n
Match if the number of existing connections is above n.
--connlimit-mask prefix_length
Group hosts using the prefix length. For IPv4, this must be a
number between (including) 0 and 32. For IPv6, between 0 and
128. If not specified, the maximum prefix length for the
applicable protocol is used.
--connlimit-saddr
Apply the limit onto the source group. This is the default if
--connlimit-daddr is not specified.
--connlimit-daddr
Apply the limit onto the destination group.
Examples:
# allow 2 telnet connections per client host
iptables -A INPUT -p tcp --syn --dport 23 -m connlimit
--connlimit-above 2 -j REJECT
# you can also match the other way around:
iptables -A INPUT -p tcp --syn --dport 23 -m connlimit
--connlimit-upto 2 -j ACCEPT
# limit the number of parallel HTTP requests to 16 per class C sized
source network (24 bit netmask)
iptables -p tcp --syn --dport 80 -m connlimit
--connlimit-above 16 --connlimit-mask 24 -j REJECT
# limit the number of parallel HTTP requests to 16 for the link local
network
(ipv6) ip6tables -p tcp --syn --dport 80 -s fe80::/64 -m
connlimit --connlimit-above 16 --connlimit-mask 64 -j REJECT
# Limit the number of connections to a particular host:
ip6tables -p tcp --syn --dport 49152:65535 -d 2001:db8::1 -m
connlimit --connlimit-above 100 -j REJECT
connmark
This module matches the netfilter mark field associated with a
connection (which can be set using the CONNMARK target below).
[!] --mark value[/mask]
Matches packets in connections with the given mark value (if a
mask is specified, this is logically ANDed with the mark
before the comparison).
conntrack
This module, when combined with connection tracking, allows access to
the connection tracking state for this packet/connection.
[!] --ctstate statelist
statelist is a comma separated list of the connection states
to match. Possible states are listed below.
[!] --ctproto l4proto
Layer-4 protocol to match (by number or name)
[!] --ctorigsrc address[/mask]
[!] --ctorigdst address[/mask]
[!] --ctreplsrc address[/mask]
[!] --ctrepldst address[/mask]
Match against original/reply source/destination address
[!] --ctorigsrcport port[:port]
[!] --ctorigdstport port[:port]
[!] --ctreplsrcport port[:port]
[!] --ctrepldstport port[:port]
Match against original/reply source/destination port
(TCP/UDP/etc.) or GRE key. Matching against port ranges is
only supported in kernel versions above 2.6.38.
[!] --ctstatus statelist
statuslist is a comma separated list of the connection
statuses to match. Possible statuses are listed below.
[!] --ctexpire time[:time]
Match remaining lifetime in seconds against given value or
range of values (inclusive)
--ctdir {ORIGINAL|REPLY}
Match packets that are flowing in the specified direction. If
this flag is not specified at all, matches packets in both
directions.
States for --ctstate:
INVALID
The packet is associated with no known connection.
NEW The packet has started a new connection or otherwise
associated with a connection which has not seen packets in
both directions.
ESTABLISHED
The packet is associated with a connection which has seen
packets in both directions.
RELATED
The packet is starting a new connection, but is associated
with an existing connection, such as an FTP data transfer or
an ICMP error.
UNTRACKED
The packet is not tracked at all, which happens if you
explicitly untrack it by using -j CT --notrack in the raw
table.
SNAT A virtual state, matching if the original source address
differs from the reply destination.
DNAT A virtual state, matching if the original destination differs
from the reply source.
Statuses for --ctstatus:
NONE None of the below.
EXPECTED
This is an expected connection (i.e. a conntrack helper set it
up).
SEEN_REPLY
Conntrack has seen packets in both directions.
ASSURED
Conntrack entry should never be early-expired.
CONFIRMED
Connection is confirmed: originating packet has left box.
cpu
[!] --cpu number
Match cpu handling this packet. cpus are numbered from 0 to
NR_CPUS-1 Can be used in combination with RPS (Remote Packet
Steering) or multiqueue NICs to spread network traffic on
different queues.
Example:
iptables -t nat -A PREROUTING -p tcp --dport 80 -m cpu --cpu 0 -j
REDIRECT --to-port 8080
iptables -t nat -A PREROUTING -p tcp --dport 80 -m cpu --cpu 1 -j
REDIRECT --to-port 8081
Available since Linux 2.6.36.
dccp
[!] --source-port,--sport port[:port]
[!] --destination-port,--dport port[:port]
[!] --dccp-types mask
Match when the DCCP packet type is one of 'mask'. 'mask' is a
comma-separated list of packet types. Packet types are:
REQUEST RESPONSE DATA ACK DATAACK CLOSEREQ CLOSE RESET SYNC
SYNCACK INVALID.
[!] --dccp-option number
Match if DCCP option set.
devgroup
Match device group of a packets incoming/outgoing interface.
[!] --src-group name
Match device group of incoming device
[!] --dst-group name
Match device group of outgoing device
dscp
This module matches the 6 bit DSCP field within the TOS field in the
IP header. DSCP has superseded TOS within the IETF.
[!] --dscp value
Match against a numeric (decimal or hex) value [0-63].
[!] --dscp-class class
Match the DiffServ class. This value may be any of the BE, EF,
AFxx or CSx classes. It will then be converted into its
according numeric value.
dst (IPv6-specific)
This module matches the parameters in Destination Options header
[!] --dst-len length
Total length of this header in octets.
--dst-opts type[:length][,type[:length]...]
numeric type of option and the length of the option data in
octets.
ecn
This allows you to match the ECN bits of the IPv4/IPv6 and TCP
header. ECN is the Explicit Congestion Notification mechanism as
specified in RFC3168
[!] --ecn-tcp-cwr
This matches if the TCP ECN CWR (Congestion Window Received)
bit is set.
[!] --ecn-tcp-ece
This matches if the TCP ECN ECE (ECN Echo) bit is set.
[!] --ecn-ip-ect num
This matches a particular IPv4/IPv6 ECT (ECN-Capable
Transport). You have to specify a number between `0' and `3'.
esp
This module matches the SPIs in ESP header of IPsec packets.
[!] --espspi spi[:spi]
eui64 (IPv6-specific)
This module matches the EUI-64 part of a stateless autoconfigured
IPv6 address. It compares the EUI-64 derived from the source MAC
address in Ethernet frame with the lower 64 bits of the IPv6 source
address. But "Universal/Local" bit is not compared. This module
doesn't match other link layer frame, and is only valid in the
PREROUTING, INPUT and FORWARD chains.
frag (IPv6-specific)
This module matches the parameters in Fragment header.
[!] --fragid id[:id]
Matches the given Identification or range of it.
[!] --fraglen length
This option cannot be used with kernel version 2.6.10 or
later. The length of Fragment header is static and this option
doesn't make sense.
--fragres
Matches if the reserved fields are filled with zero.
--fragfirst
Matches on the first fragment.
--fragmore
Matches if there are more fragments.
--fraglast
Matches if this is the last fragment.
hashlimit
hashlimit uses hash buckets to express a rate limiting match (like
the limit match) for a group of connections using a single iptables
rule. Grouping can be done per-hostgroup (source and/or destination
address) and/or per-port. It gives you the ability to express "N
packets per time quantum per group" or "N bytes per seconds" (see
below for some examples).
A hash limit option (--hashlimit-upto, --hashlimit-above) and
--hashlimit-name are required.
--hashlimit-upto amount[/second|/minute|/hour|/day]
Match if the rate is below or equal to amount/quantum. It is
specified either as a number, with an optional time quantum
suffix (the default is 3/hour), or as amountb/second (number
of bytes per second).
--hashlimit-above amount[/second|/minute|/hour|/day]
Match if the rate is above amount/quantum.
--hashlimit-burst amount
Maximum initial number of packets to match: this number gets
recharged by one every time the limit specified above is not
reached, up to this number; the default is 5. When byte-based
rate matching is requested, this option specifies the amount
of bytes that can exceed the given rate. This option should
be used with caution -- if the entry expires, the burst value
is reset too.
--hashlimit-mode {srcip|srcport|dstip|dstport},...
A comma-separated list of objects to take into consideration.
If no --hashlimit-mode option is given, hashlimit acts like
limit, but at the expensive of doing the hash housekeeping.
--hashlimit-srcmask prefix
When --hashlimit-mode srcip is used, all source addresses
encountered will be grouped according to the given prefix
length and the so-created subnet will be subject to hashlimit.
prefix must be between (inclusive) 0 and 32. Note that
--hashlimit-srcmask 0 is basically doing the same thing as not
specifying srcip for --hashlimit-mode, but is technically more
expensive.
--hashlimit-dstmask prefix
Like --hashlimit-srcmask, but for destination addresses.
--hashlimit-name foo
The name for the /proc/net/ipt_hashlimit/foo entry.
--hashlimit-htable-size buckets
The number of buckets of the hash table
--hashlimit-htable-max entries
Maximum entries in the hash.
--hashlimit-htable-expire msec
After how many milliseconds do hash entries expire.
--hashlimit-htable-gcinterval msec
How many milliseconds between garbage collection intervals.
--hashlimit-rate-match
Classify the flow instead of rate-limiting it. This acts like
a true/flase match on whether the rate is above/below a
certain number
--hashlimit-rate-interval sec
Can be used with --hashlimit-rate-match to specify the
interval at which the rate should be sampled
Examples:
matching on source host
"1000 packets per second for every host in 192.168.0.0/16" =>
-s 192.168.0.0/16 --hashlimit-mode srcip --hashlimit-upto
1000/sec
matching on source port
"100 packets per second for every service of 192.168.1.1" =>
-s 192.168.1.1 --hashlimit-mode srcport --hashlimit-upto
100/sec
matching on subnet
"10000 packets per minute for every /28 subnet (groups of 8
addresses) in 10.0.0.0/8" => -s 10.0.0.0/8 --hashlimit-mask 28
--hashlimit-upto 10000/min
matching bytes per second
"flows exceeding 512kbyte/s" => --hashlimit-mode
srcip,dstip,srcport,dstport --hashlimit-above 512kb/s
matching bytes per second
"hosts that exceed 512kbyte/s, but permit up to 1Megabytes
without matching" --hashlimit-mode dstip --hashlimit-above
512kb/s --hashlimit-burst 1mb
hbh (IPv6-specific)
This module matches the parameters in Hop-by-Hop Options header
[!] --hbh-len length
Total length of this header in octets.
--hbh-opts type[:length][,type[:length]...]
numeric type of option and the length of the option data in
octets.
helper
This module matches packets related to a specific conntrack-helper.
[!] --helper string
Matches packets related to the specified conntrack-helper.
string can be "ftp" for packets related to a ftp-session on
default port. For other ports append -portnr to the value,
ie. "ftp-2121".
Same rules apply for other conntrack-helpers.
hl (IPv6-specific)
This module matches the Hop Limit field in the IPv6 header.
[!] --hl-eq value
Matches if Hop Limit equals value.
--hl-lt value
Matches if Hop Limit is less than value.
--hl-gt value
Matches if Hop Limit is greater than value.
icmp (IPv4-specific)
This extension can be used if `--protocol icmp' is specified. It
provides the following option:
[!] --icmp-type {type[/code]|typename}
This allows specification of the ICMP type, which can be a
numeric ICMP type, type/code pair, or one of the ICMP type
names shown by the command
iptables -p icmp -h
icmp6 (IPv6-specific)
This extension can be used if `--protocol ipv6-icmp' or `--protocol
icmpv6' is specified. It provides the following option:
[!] --icmpv6-type type[/code]|typename
This allows specification of the ICMPv6 type, which can be a
numeric ICMPv6 type, type and code, or one of the ICMPv6 type
names shown by the command
ip6tables -p ipv6-icmp -h
iprange
This matches on a given arbitrary range of IP addresses.
[!] --src-range from[-to]
Match source IP in the specified range.
[!] --dst-range from[-to]
Match destination IP in the specified range.
ipv6header (IPv6-specific)
This module matches IPv6 extension headers and/or upper layer header.
--soft Matches if the packet includes any of the headers specified
with --header.
[!] --header header[,header...]
Matches the packet which EXACTLY includes all specified
headers. The headers encapsulated with ESP header are out of
scope. Possible header types can be:
hop|hop-by-hop
Hop-by-Hop Options header
dst Destination Options header
route Routing header
frag Fragment header
auth Authentication header
esp Encapsulating Security Payload header
none No Next header which matches 59 in the 'Next Header field' of
IPv6 header or any IPv6 extension headers
prot which matches any upper layer protocol header. A protocol name
from /etc/protocols and numeric value also allowed. The number
255 is equivalent to prot.
ipvs
Match IPVS connection properties.
[!] --ipvs
packet belongs to an IPVS connection
Any of the following options implies --ipvs (even negated)
[!] --vproto protocol
VIP protocol to match; by number or name, e.g. "tcp"
[!] --vaddr address[/mask]
VIP address to match
[!] --vport port
VIP port to match; by number or name, e.g. "http"
--vdir {ORIGINAL|REPLY}
flow direction of packet
[!] --vmethod {GATE|IPIP|MASQ}
IPVS forwarding method used
[!] --vportctl port
VIP port of the controlling connection to match, e.g. 21 for
FTP
length
This module matches the length of the layer-3 payload (e.g. layer-4
packet) of a packet against a specific value or range of values.
[!] --length length[:length]
limit
This module matches at a limited rate using a token bucket filter. A
rule using this extension will match until this limit is reached. It
can be used in combination with the LOG target to give limited
logging, for example.
xt_limit has no negation support - you will have to use -m hashlimit
! --hashlimit rate in this case whilst omitting --hashlimit-mode.
--limit rate[/second|/minute|/hour|/day]
Maximum average matching rate: specified as a number, with an
optional `/second', `/minute', `/hour', or `/day' suffix; the
default is 3/hour.
--limit-burst number
Maximum initial number of packets to match: this number gets
recharged by one every time the limit specified above is not
reached, up to this number; the default is 5.
mac
[!] --mac-source address
Match source MAC address. It must be of the form
XX:XX:XX:XX:XX:XX. Note that this only makes sense for
packets coming from an Ethernet device and entering the
PREROUTING, FORWARD or INPUT chains.
mark
This module matches the netfilter mark field associated with a packet
(which can be set using the MARK target below).
[!] --mark value[/mask]
Matches packets with the given unsigned mark value (if a mask
is specified, this is logically ANDed with the mask before the
comparison).
mh (IPv6-specific)
This extension is loaded if `--protocol ipv6-mh' or `--protocol mh'
is specified. It provides the following option:
[!] --mh-type type[:type]
This allows specification of the Mobility Header(MH) type,
which can be a numeric MH type, type or one of the MH type
names shown by the command
ip6tables -p mh -h
multiport
This module matches a set of source or destination ports. Up to 15
ports can be specified. A port range (port:port) counts as two
ports. It can only be used in conjunction with one of the following
protocols: tcp, udp, udplite, dccp and sctp.
[!] --source-ports,--sports port[,port|,port:port]...
Match if the source port is one of the given ports. The flag
--sports is a convenient alias for this option. Multiple ports
or port ranges are separated using a comma, and a port range
is specified using a colon. 53,1024:65535 would therefore
match ports 53 and all from 1024 through 65535.
[!] --destination-ports,--dports port[,port|,port:port]...
Match if the destination port is one of the given ports. The
flag --dports is a convenient alias for this option.
[!] --ports port[,port|,port:port]...
Match if either the source or destination ports are equal to
one of the given ports.
nfacct
The nfacct match provides the extended accounting infrastructure for
iptables. You have to use this match together with the standalone
user-space utility nfacct(8)
The only option available for this match is the following:
--nfacct-name name
This allows you to specify the existing object name that will
be use for accounting the traffic that this rule-set is
matching.
To use this extension, you have to create an accounting object:
nfacct add http-traffic
Then, you have to attach it to the accounting object via iptables:
iptables -I INPUT -p tcp --sport 80 -m nfacct --nfacct-name
http-traffic
iptables -I OUTPUT -p tcp --dport 80 -m nfacct --nfacct-name
http-traffic
Then, you can check for the amount of traffic that the rules match:
nfacct get http-traffic
{ pkts = 00000000000000000156, bytes = 00000000000000151786 }
= http-traffic;
You can obtain nfacct(8) from http://www.netfilter.org or,
alternatively, from the git.netfilter.org repository.
osf
The osf module does passive operating system fingerprinting. This
modules compares some data (Window Size, MSS, options and their
order, TTL, DF, and others) from packets with the SYN bit set.
[!] --genre string
Match an operating system genre by using a passive
fingerprinting.
--ttl level
Do additional TTL checks on the packet to determine the
operating system. level can be one of the following values:
· 0 - True IP address and fingerprint TTL comparison. This
generally works for LANs.
· 1 - Check if the IP header's TTL is less than the fingerprint
one. Works for globally-routable addresses.
· 2 - Do not compare the TTL at all.
--log level
Log determined genres into dmesg even if they do not match the
desired one. level can be one of the following values:
· 0 - Log all matched or unknown signatures
· 1 - Log only the first one
· 2 - Log all known matched signatures
You may find something like this in syslog:
Windows [2000:SP3:Windows XP Pro SP1, 2000 SP3]: 11.22.33.55:4024 ->
11.22.33.44:139 hops=3 Linux [2.5-2.6:] : 1.2.3.4:42624 -> 1.2.3.5:22
hops=4
OS fingerprints are loadable using the nfnl_osf program. To load
fingerprints from a file, use:
nfnl_osf -f /usr/share/xtables/pf.os
To remove them again,
nfnl_osf -f /usr/share/xtables/pf.os -d
The fingerprint database can be downlaoded from
http://www.openbsd.org/cgi-bin/cvsweb/src/etc/pf.os .
owner
This module attempts to match various characteristics of the packet
creator, for locally generated packets. This match is only valid in
the OUTPUT and POSTROUTING chains. Forwarded packets do not have any
socket associated with them. Packets from kernel threads do have a
socket, but usually no owner.
[!] --uid-owner username
[!] --uid-owner userid[-userid]
Matches if the packet socket's file structure (if it has one)
is owned by the given user. You may also specify a numerical
UID, or an UID range.
[!] --gid-owner groupname
[!] --gid-owner groupid[-groupid]
Matches if the packet socket's file structure is owned by the
given group. You may also specify a numerical GID, or a GID
range.
[!] --socket-exists
Matches if the packet is associated with a socket.
physdev
This module matches on the bridge port input and output devices
enslaved to a bridge device. This module is a part of the
infrastructure that enables a transparent bridging IP firewall and is
only useful for kernel versions above version 2.5.44.
[!] --physdev-in name
Name of a bridge port via which a packet is received (only for
packets entering the INPUT, FORWARD and PREROUTING chains). If
the interface name ends in a "+", then any interface which
begins with this name will match. If the packet didn't arrive
through a bridge device, this packet won't match this option,
unless '!' is used.
[!] --physdev-out name
Name of a bridge port via which a packet is going to be sent
(for bridged packets entering the FORWARD and POSTROUTING
chains). If the interface name ends in a "+", then any
interface which begins with this name will match.
[!] --physdev-is-in
Matches if the packet has entered through a bridge interface.
[!] --physdev-is-out
Matches if the packet will leave through a bridge interface.
[!] --physdev-is-bridged
Matches if the packet is being bridged and therefore is not
being routed. This is only useful in the FORWARD and
POSTROUTING chains.
pkttype
This module matches the link-layer packet type.
[!] --pkt-type {unicast|broadcast|multicast}
policy
This modules matches the policy used by IPsec for handling a packet.
--dir {in|out}
Used to select whether to match the policy used for
decapsulation or the policy that will be used for
encapsulation. in is valid in the PREROUTING, INPUT and
FORWARD chains, out is valid in the POSTROUTING, OUTPUT and
FORWARD chains.
--pol {none|ipsec}
Matches if the packet is subject to IPsec processing. --pol
none cannot be combined with --strict.
--strict
Selects whether to match the exact policy or match if any rule
of the policy matches the given policy.
For each policy element that is to be described, one can use one or
more of the following options. When --strict is in effect, at least
one must be used per element.
[!] --reqid id
Matches the reqid of the policy rule. The reqid can be
specified with setkey(8) using unique:id as level.
[!] --spi spi
Matches the SPI of the SA.
[!] --proto {ah|esp|ipcomp}
Matches the encapsulation protocol.
[!] --mode {tunnel|transport}
Matches the encapsulation mode.
[!] --tunnel-src addr[/mask]
Matches the source end-point address of a tunnel mode SA.
Only valid with --mode tunnel.
[!] --tunnel-dst addr[/mask]
Matches the destination end-point address of a tunnel mode SA.
Only valid with --mode tunnel.
--next Start the next element in the policy specification. Can only
be used with --strict.
quota
Implements network quotas by decrementing a byte counter with each
packet. The condition matches until the byte counter reaches zero.
Behavior is reversed with negation (i.e. the condition does not match
until the byte counter reaches zero).
[!] --quota bytes
The quota in bytes.
rateest
The rate estimator can match on estimated rates as collected by the
RATEEST target. It supports matching on absolute bps/pps values,
comparing two rate estimators and matching on the difference between
two rate estimators.
For a better understanding of the available options, these are all
possible combinations:
· rateest operator rateest-bps
· rateest operator rateest-pps
· (rateest minus rateest-bps1) operator rateest-bps2
· (rateest minus rateest-pps1) operator rateest-pps2
· rateest1 operator rateest2 rateest-bps(without rate!)
· rateest1 operator rateest2 rateest-pps(without rate!)
· (rateest1 minus rateest-bps1) operator (rateest2 minus rateest-
bps2)
· (rateest1 minus rateest-pps1) operator (rateest2 minus rateest-
pps2)
--rateest-delta
For each estimator (either absolute or relative mode), calculate
the difference between the estimator-determined flow rate and the
static value chosen with the BPS/PPS options. If the flow rate is
higher than the specified BPS/PPS, 0 will be used instead of a
negative value. In other words, "max(0, rateest#_rate -
rateest#_bps)" is used.
[!] --rateest-lt
Match if rate is less than given rate/estimator.
[!] --rateest-gt
Match if rate is greater than given rate/estimator.
[!] --rateest-eq
Match if rate is equal to given rate/estimator.
In the so-called "absolute mode", only one rate estimator is used and
compared against a static value, while in "relative mode", two rate
estimators are compared against another.
--rateest name
Name of the one rate estimator for absolute mode.
--rateest1 name
--rateest2 name
The names of the two rate estimators for relative mode.
--rateest-bps [value]
--rateest-pps [value]
--rateest-bps1 [value]
--rateest-bps2 [value]
--rateest-pps1 [value]
--rateest-pps2 [value]
Compare the estimator(s) by bytes or packets per second, and
compare against the chosen value. See the above bullet list
for which option is to be used in which case. A unit suffix
may be used - available ones are: bit, [kmgt]bit, [KMGT]ibit,
Bps, [KMGT]Bps, [KMGT]iBps.
Example: This is what can be used to route outgoing data connections
from an FTP server over two lines based on the available bandwidth at
the time the data connection was started:
# Estimate outgoing rates
iptables -t mangle -A POSTROUTING -o eth0 -j RATEEST --rateest-name
eth0 --rateest-interval 250ms --rateest-ewma 0.5s
iptables -t mangle -A POSTROUTING -o ppp0 -j RATEEST --rateest-name
ppp0 --rateest-interval 250ms --rateest-ewma 0.5s
# Mark based on available bandwidth
iptables -t mangle -A balance -m conntrack --ctstate NEW -m helper
--helper ftp -m rateest --rateest-delta --rateest1 eth0
--rateest-bps1 2.5mbit --rateest-gt --rateest2 ppp0 --rateest-bps2
2mbit -j CONNMARK --set-mark 1
iptables -t mangle -A balance -m conntrack --ctstate NEW -m helper
--helper ftp -m rateest --rateest-delta --rateest1 ppp0
--rateest-bps1 2mbit --rateest-gt --rateest2 eth0 --rateest-bps2
2.5mbit -j CONNMARK --set-mark 2
iptables -t mangle -A balance -j CONNMARK --restore-mark
realm (IPv4-specific)
This matches the routing realm. Routing realms are used in complex
routing setups involving dynamic routing protocols like BGP.
[!] --realm value[/mask]
Matches a given realm number (and optionally mask). If not a
number, value can be a named realm from
/etc/iproute2/rt_realms (mask can not be used in that case).
recent
Allows you to dynamically create a list of IP addresses and then
match against that list in a few different ways.
For example, you can create a "badguy" list out of people attempting
to connect to port 139 on your firewall and then DROP all future
packets from them without considering them.
--set, --rcheck, --update and --remove are mutually exclusive.
--name name
Specify the list to use for the commands. If no name is given
then DEFAULT will be used.
[!] --set
This will add the source address of the packet to the list. If
the source address is already in the list, this will update
the existing entry. This will always return success (or
failure if ! is passed in).
--rsource
Match/save the source address of each packet in the recent
list table. This is the default.
--rdest
Match/save the destination address of each packet in the
recent list table.
--mask netmask
Netmask that will be applied to this recent list.
[!] --rcheck
Check if the source address of the packet is currently in the
list.
[!] --update
Like --rcheck, except it will update the "last seen" timestamp
if it matches.
[!] --remove
Check if the source address of the packet is currently in the
list and if so that address will be removed from the list and
the rule will return true. If the address is not found, false
is returned.
--seconds seconds
This option must be used in conjunction with one of --rcheck
or --update. When used, this will narrow the match to only
happen when the address is in the list and was seen within the
last given number of seconds.
--reap This option can only be used in conjunction with --seconds.
When used, this will cause entries older than the last given
number of seconds to be purged.
--hitcount hits
This option must be used in conjunction with one of --rcheck
or --update. When used, this will narrow the match to only
happen when the address is in the list and packets had been
received greater than or equal to the given value. This option
may be used along with --seconds to create an even narrower
match requiring a certain number of hits within a specific
time frame. The maximum value for the hitcount parameter is
given by the "ip_pkt_list_tot" parameter of the xt_recent
kernel module. Exceeding this value on the command line will
cause the rule to be rejected.
--rttl This option may only be used in conjunction with one of
--rcheck or --update. When used, this will narrow the match to
only happen when the address is in the list and the TTL of the
current packet matches that of the packet which hit the --set
rule. This may be useful if you have problems with people
faking their source address in order to DoS you via this
module by disallowing others access to your site by sending
bogus packets to you.
Examples:
iptables -A FORWARD -m recent --name badguy --rcheck --seconds
60 -j DROP
iptables -A FORWARD -p tcp -i eth0 --dport 139 -m recent
--name badguy --set -j DROP
/proc/net/xt_recent/* are the current lists of addresses and
information about each entry of each list.
Each file in /proc/net/xt_recent/ can be read from to see the current
list or written two using the following commands to modify the list:
echo +addr >/proc/net/xt_recent/DEFAULT
to add addr to the DEFAULT list
echo -addr >/proc/net/xt_recent/DEFAULT
to remove addr from the DEFAULT list
echo / >/proc/net/xt_recent/DEFAULT
to flush the DEFAULT list (remove all entries).
The module itself accepts parameters, defaults shown:
ip_list_tot=100
Number of addresses remembered per table.
ip_pkt_list_tot=20
Number of packets per address remembered.
ip_list_hash_size=0
Hash table size. 0 means to calculate it based on ip_list_tot,
default: 512.
ip_list_perms=0644
Permissions for /proc/net/xt_recent/* files.
ip_list_uid=0
Numerical UID for ownership of /proc/net/xt_recent/* files.
ip_list_gid=0
Numerical GID for ownership of /proc/net/xt_recent/* files.
rpfilter
Performs a reverse path filter test on a packet. If a reply to the
packet would be sent via the same interface that the packet arrived
on, the packet will match. Note that, unlike the in-kernel
rp_filter, packets protected by IPSec are not treated specially.
Combine this match with the policy match if you want this. Also,
packets arriving via the loopback interface are always permitted.
This match can only be used in the PREROUTING chain of the raw or
mangle table.
--loose
Used to specify that the reverse path filter test should match
even if the selected output device is not the expected one.
--validmark
Also use the packets' nfmark value when performing the reverse
path route lookup.
--accept-local
This will permit packets arriving from the network with a
source address that is also assigned to the local machine.
--invert
This will invert the sense of the match. Instead of matching
packets that passed the reverse path filter test, match those
that have failed it.
Example to log and drop packets failing the reverse path filter test:
iptables -t raw -N RPFILTER
iptables -t raw -A RPFILTER -m rpfilter -j RETURN
iptables -t raw -A RPFILTER -m limit --limit 10/minute -j NFLOG
--nflog-prefix "rpfilter drop"
iptables -t raw -A RPFILTER -j DROP
iptables -t raw -A PREROUTING -j RPFILTER
Example to drop failed packets, without logging:
iptables -t raw -A RPFILTER -m rpfilter --invert -j DROP
rt (IPv6-specific)
Match on IPv6 routing header
[!] --rt-type type
Match the type (numeric).
[!] --rt-segsleft num[:num]
Match the `segments left' field (range).
[!] --rt-len length
Match the length of this header.
--rt-0-res
Match the reserved field, too (type=0)
--rt-0-addrs addr[,addr...]
Match type=0 addresses (list).
--rt-0-not-strict
List of type=0 addresses is not a strict list.
sctp
[!] --source-port,--sport port[:port]
[!] --destination-port,--dport port[:port]
[!] --chunk-types {all|any|only} chunktype[:flags] [...]
The flag letter in upper case indicates that the flag is to
match if set, in the lower case indicates to match if unset.
Chunk types: DATA INIT INIT_ACK SACK HEARTBEAT HEARTBEAT_ACK
ABORT SHUTDOWN SHUTDOWN_ACK ERROR COOKIE_ECHO COOKIE_ACK
ECN_ECNE ECN_CWR SHUTDOWN_COMPLETE ASCONF ASCONF_ACK
FORWARD_TSN
chunk type available flags
DATA I U B E i u b e
ABORT T t
SHUTDOWN_COMPLETE T t
(lowercase means flag should be "off", uppercase means "on")
Examples:
iptables -A INPUT -p sctp --dport 80 -j DROP
iptables -A INPUT -p sctp --chunk-types any DATA,INIT -j DROP
iptables -A INPUT -p sctp --chunk-types any DATA:Be -j ACCEPT
set
This module matches IP sets which can be defined by ipset(8).
[!] --match-set setname flag[,flag]...
where flags are the comma separated list of src and/or dst
specifications and there can be no more than six of them.
Hence the command
iptables -A FORWARD -m set --match-set test src,dst
will match packets, for which (if the set type is ipportmap)
the source address and destination port pair can be found in
the specified set. If the set type of the specified set is
single dimension (for example ipmap), then the command will
match packets for which the source address can be found in the
specified set.
--return-nomatch
If the --return-nomatch option is specified and the set type
supports the nomatch flag, then the matching is reversed: a
match with an element flagged with nomatch returns true, while
a match with a plain element returns false.
! --update-counters
If the --update-counters flag is negated, then the packet and
byte counters of the matching element in the set won't be
updated. Default the packet and byte counters are updated.
! --update-subcounters
If the --update-subcounters flag is negated, then the packet
and byte counters of the matching element in the member set of
a list type of set won't be updated. Default the packet and
byte counters are updated.
[!] --packets-eq value
If the packet is matched an element in the set, match only if
the packet counter of the element matches the given value too.
--packets-lt value
If the packet is matched an element in the set, match only if
the packet counter of the element is less than the given value
as well.
--packets-gt value
If the packet is matched an element in the set, match only if
the packet counter of the element is greater than the given
value as well.
[!] --bytes-eq value
If the packet is matched an element in the set, match only if
the byte counter of the element matches the given value too.
--bytes-lt value
If the packet is matched an element in the set, match only if
the byte counter of the element is less than the given value
as well.
--bytes-gt value
If the packet is matched an element in the set, match only if
the byte counter of the element is greater than the given
value as well.
The packet and byte counters related options and flags are ignored
when the set was defined without counter support.
The option --match-set can be replaced by --set if that does not
clash with an option of other extensions.
Use of -m set requires that ipset kernel support is provided, which,
for standard kernels, is the case since Linux 2.6.39.
socket
This matches if an open TCP/UDP socket can be found by doing a socket
lookup on the packet. It matches if there is an established or
non-zero bound listening socket (possibly with a non-local address).
The lookup is performed using the packet tuple of TCP/UDP packets, or
the original TCP/UDP header embedded in an ICMP/ICPMv6 error packet.
--transparent
Ignore non-transparent sockets.
--nowildcard
Do not ignore sockets bound to 'any' address. The socket
match won't accept zero-bound listeners by default, since then
local services could intercept traffic that would otherwise be
forwarded. This option therefore has security implications
when used to match traffic being forwarded to redirect such
packets to local machine with policy routing. When using the
socket match to implement fully transparent proxies bound to
non-local addresses it is recommended to use the --transparent
option instead.
Example (assuming packets with mark 1 are delivered locally):
-t mangle -A PREROUTING -m socket --transparent -j MARK
--set-mark 1
--restore-skmark
Set the packet mark to the matching socket's mark. Can be
combined with the --transparent and --nowildcard options to
restrict the sockets to be matched when restoring the packet
mark.
Example: An application opens 2 transparent (IP_TRANSPARENT) sockets
and sets a mark on them with SO_MARK socket option. We can filter
matching packets:
-t mangle -I PREROUTING -m socket --transparent --restore-
skmark -j action
-t mangle -A action -m mark --mark 10 -j action2
-t mangle -A action -m mark --mark 11 -j action3
state
The "state" extension is a subset of the "conntrack" module. "state"
allows access to the connection tracking state for this packet.
[!] --state state
Where state is a comma separated list of the connection states
to match. Only a subset of the states unterstood by
"conntrack" are recognized: INVALID, ESTABLISHED, NEW, RELATED
or UNTRACKED. For their description, see the "conntrack"
heading in this manpage.
statistic
This module matches packets based on some statistic condition. It
supports two distinct modes settable with the --mode option.
Supported options:
--mode mode
Set the matching mode of the matching rule, supported modes
are random and nth.
[!] --probability p
Set the probability for a packet to be randomly matched. It
only works with the random mode. p must be within 0.0 and 1.0.
The supported granularity is in 1/2147483648th increments.
[!] --every n
Match one packet every nth packet. It works only with the nth
mode (see also the --packet option).
--packet p
Set the initial counter value (0 <= p <= n-1, default 0) for
the nth mode.
string
This modules matches a given string by using some pattern matching
strategy. It requires a linux kernel >= 2.6.14.
--algo {bm|kmp}
Select the pattern matching strategy. (bm = Boyer-Moore, kmp =
Knuth-Pratt-Morris)
--from offset
Set the offset from which it starts looking for any matching.
If not passed, default is 0.
--to offset
Set the offset up to which should be scanned. That is, byte
offset-1 (counting from 0) is the last one that is scanned.
If not passed, default is the packet size.
[!] --string pattern
Matches the given pattern.
[!] --hex-string pattern
Matches the given pattern in hex notation.
--icase
Ignore case when searching.
Examples:
# The string pattern can be used for simple text characters.
iptables -A INPUT -p tcp --dport 80 -m string --algo bm
--string 'GET /index.html' -j LOG
# The hex string pattern can be used for non-printable
characters, like |0D 0A| or |0D0A|.
iptables -p udp --dport 53 -m string --algo bm --from 40 --to
57 --hex-string '|03|www|09|netfilter|03|org|00|'
tcp
These extensions can be used if `--protocol tcp' is specified. It
provides the following options:
[!] --source-port,--sport port[:port]
Source port or port range specification. This can either be a
service name or a port number. An inclusive range can also be
specified, using the format first:last. If the first port is
omitted, "0" is assumed; if the last is omitted, "65535" is
assumed. The flag --sport is a convenient alias for this
option.
[!] --destination-port,--dport port[:port]
Destination port or port range specification. The flag
--dport is a convenient alias for this option.
[!] --tcp-flags mask comp
Match when the TCP flags are as specified. The first argument
mask is the flags which we should examine, written as a comma-
separated list, and the second argument comp is a comma-
separated list of flags which must be set. Flags are: SYN ACK
FIN RST URG PSH ALL NONE. Hence the command
iptables -A FORWARD -p tcp --tcp-flags SYN,ACK,FIN,RST SYN
will only match packets with the SYN flag set, and the ACK,
FIN and RST flags unset.
[!] --syn
Only match TCP packets with the SYN bit set and the ACK,RST
and FIN bits cleared. Such packets are used to request TCP
connection initiation; for example, blocking such packets
coming in an interface will prevent incoming TCP connections,
but outgoing TCP connections will be unaffected. It is
equivalent to --tcp-flags SYN,RST,ACK,FIN SYN. If the "!"
flag precedes the "--syn", the sense of the option is
inverted.
[!] --tcp-option number
Match if TCP option set.
tcpmss
This matches the TCP MSS (maximum segment size) field of the TCP
header. You can only use this on TCP SYN or SYN/ACK packets, since
the MSS is only negotiated during the TCP handshake at connection
startup time.
[!] --mss value[:value]
Match a given TCP MSS value or range. If a range is given, the
second value must be greater than or equal to the first value.
time
This matches if the packet arrival time/date is within a given range.
All options are optional, but are ANDed when specified. All times are
interpreted as UTC by default.
--datestart YYYY[-MM[-DD[Thh[:mm[:ss]]]]]
--datestop YYYY[-MM[-DD[Thh[:mm[:ss]]]]]
Only match during the given time, which must be in ISO 8601
"T" notation. The possible time range is 1970-01-01T00:00:00
to 2038-01-19T04:17:07.
If --datestart or --datestop are not specified, it will
default to 1970-01-01 and 2038-01-19, respectively.
--timestart hh:mm[:ss]
--timestop hh:mm[:ss]
Only match during the given daytime. The possible time range
is 00:00:00 to 23:59:59. Leading zeroes are allowed (e.g.
"06:03") and correctly interpreted as base-10.
[!] --monthdays day[,day...]
Only match on the given days of the month. Possible values are
1 to 31. Note that specifying 31 will of course not match on
months which do not have a 31st day; the same goes for 28- or
29-day February.
[!] --weekdays day[,day...]
Only match on the given weekdays. Possible values are Mon,
Tue, Wed, Thu, Fri, Sat, Sun, or values from 1 to 7,
respectively. You may also use two-character variants (Mo, Tu,
etc.).
--contiguous
When --timestop is smaller than --timestart value, match this
as a single time period instead distinct intervals. See
EXAMPLES.
--kerneltz
Use the kernel timezone instead of UTC to determine whether a
packet meets the time regulations.
About kernel timezones: Linux keeps the system time in UTC, and
always does so. On boot, system time is initialized from a
referential time source. Where this time source has no timezone
information, such as the x86 CMOS RTC, UTC will be assumed. If the
time source is however not in UTC, userspace should provide the
correct system time and timezone to the kernel once it has the
information.
Local time is a feature on top of the (timezone independent) system
time. Each process has its own idea of local time, specified via the
TZ environment variable. The kernel also has its own timezone offset
variable. The TZ userspace environment variable specifies how the
UTC-based system time is displayed, e.g. when you run date(1), or
what you see on your desktop clock. The TZ string may resolve to
different offsets at different dates, which is what enables the
automatic time-jumping in userspace. when DST changes. The kernel's
timezone offset variable is used when it has to convert between non-
UTC sources, such as FAT filesystems, to UTC (since the latter is
what the rest of the system uses).
The caveat with the kernel timezone is that Linux distributions may
ignore to set the kernel timezone, and instead only set the system
time. Even if a particular distribution does set the timezone at
boot, it is usually does not keep the kernel timezone offset - which
is what changes on DST - up to date. ntpd will not touch the kernel
timezone, so running it will not resolve the issue. As such, one may
encounter a timezone that is always +0000, or one that is wrong half
of the time of the year. As such, using --kerneltz is highly
discouraged.
EXAMPLES. To match on weekends, use:
-m time --weekdays Sa,Su
Or, to match (once) on a national holiday block:
-m time --datestart 2007-12-24 --datestop 2007-12-27
Since the stop time is actually inclusive, you would need the
following stop time to not match the first second of the new day:
-m time --datestart 2007-01-01T17:00 --datestop
2007-01-01T23:59:59
During lunch hour:
-m time --timestart 12:30 --timestop 13:30
The fourth Friday in the month:
-m time --weekdays Fr --monthdays 22,23,24,25,26,27,28
(Note that this exploits a certain mathematical property. It is not
possible to say "fourth Thursday OR fourth Friday" in one rule. It is
possible with multiple rules, though.)
Matching across days might not do what is expected. For instance,
-m time --weekdays Mo --timestart 23:00 --timestop 01:00 Will
match Monday, for one hour from midnight to 1 a.m., and then
again for another hour from 23:00 onwards. If this is
unwanted, e.g. if you would like 'match for two hours from
Montay 23:00 onwards' you need to also specify the
--contiguous option in the example above.
tos
This module matches the 8-bit Type of Service field in the IPv4
header (i.e. including the "Precedence" bits) or the (also 8-bit)
Priority field in the IPv6 header.
[!] --tos value[/mask]
Matches packets with the given TOS mark value. If a mask is
specified, it is logically ANDed with the TOS mark before the
comparison.
[!] --tos symbol
You can specify a symbolic name when using the tos match for
IPv4. The list of recognized TOS names can be obtained by
calling iptables with -m tos -h. Note that this implies a
mask of 0x3F, i.e. all but the ECN bits.
ttl (IPv4-specific)
This module matches the time to live field in the IP header.
[!] --ttl-eq ttl
Matches the given TTL value.
--ttl-gt ttl
Matches if TTL is greater than the given TTL value.
--ttl-lt ttl
Matches if TTL is less than the given TTL value.
u32
U32 tests whether quantities of up to 4 bytes extracted from a packet
have specified values. The specification of what to extract is
general enough to find data at given offsets from tcp headers or
payloads.
[!] --u32 tests
The argument amounts to a program in a small language
described below.
tests := location "=" value | tests "&&" location "=" value
value := range | value "," range
range := number | number ":" number
a single number, n, is interpreted the same as n:n. n:m is
interpreted as the range of numbers >=n and <=m.
location := number | location operator number
operator := "&" | "<<" | ">>" | "@"
The operators &, <<, >> and && mean the same as in C. The = is
really a set membership operator and the value syntax describes a
set. The @ operator is what allows moving to the next header and is
described further below.
There are currently some artificial implementation limits on the size
of the tests:
* no more than 10 of "=" (and 9 "&&"s) in the u32 argument
* no more than 10 ranges (and 9 commas) per value
* no more than 10 numbers (and 9 operators) per location
To describe the meaning of location, imagine the following machine
that interprets it. There are three registers:
A is of type char *, initially the address of the IP header
B and C are unsigned 32 bit integers, initially zero
The instructions are:
number B = number;
C = (*(A+B)<<24) + (*(A+B+1)<<16) + (*(A+B+2)<<8) + *(A+B+3)
&number C = C & number
<< number C = C << number
>> number C = C >> number
@number A = A + C; then do the instruction number
Any access of memory outside [skb->data,skb->end] causes the match to
fail. Otherwise the result of the computation is the final value of
C.
Whitespace is allowed but not required in the tests. However, the
characters that do occur there are likely to require shell quoting,
so it is a good idea to enclose the arguments in quotes.
Example:
match IP packets with total length >= 256
The IP header contains a total length field in bytes 2-3.
--u32 "0 & 0xFFFF = 0x100:0xFFFF"
read bytes 0-3
AND that with 0xFFFF (giving bytes 2-3), and test whether that
is in the range [0x100:0xFFFF]
Example: (more realistic, hence more complicated)
match ICMP packets with icmp type 0
First test that it is an ICMP packet, true iff byte 9
(protocol) = 1
--u32 "6 & 0xFF = 1 && ...
read bytes 6-9, use & to throw away bytes 6-8 and compare the
result to 1. Next test that it is not a fragment. (If so, it
might be part of such a packet but we cannot always tell.)
N.B.: This test is generally needed if you want to match
anything beyond the IP header. The last 6 bits of byte 6 and
all of byte 7 are 0 iff this is a complete packet (not a
fragment). Alternatively, you can allow first fragments by
only testing the last 5 bits of byte 6.
... 4 & 0x3FFF = 0 && ...
Last test: the first byte past the IP header (the type) is 0.
This is where we have to use the @syntax. The length of the IP
header (IHL) in 32 bit words is stored in the right half of
byte 0 of the IP header itself.
... 0 >> 22 & 0x3C @ 0 >> 24 = 0"
The first 0 means read bytes 0-3, >>22 means shift that 22
bits to the right. Shifting 24 bits would give the first byte,
so only 22 bits is four times that plus a few more bits. &3C
then eliminates the two extra bits on the right and the first
four bits of the first byte. For instance, if IHL=5, then the
IP header is 20 (4 x 5) bytes long. In this case, bytes 0-1
are (in binary) xxxx0101 yyzzzzzz, >>22 gives the 10 bit value
xxxx0101yy and &3C gives 010100. @ means to use this number as
a new offset into the packet, and read four bytes starting
from there. This is the first 4 bytes of the ICMP payload, of
which byte 0 is the ICMP type. Therefore, we simply shift the
value 24 to the right to throw out all but the first byte and
compare the result with 0.
Example:
TCP payload bytes 8-12 is any of 1, 2, 5 or 8
First we test that the packet is a tcp packet (similar to
ICMP).
--u32 "6 & 0xFF = 6 && ...
Next, test that it is not a fragment (same as above).
... 0 >> 22 & 0x3C @ 12 >> 26 & 0x3C @ 8 = 1,2,5,8"
0>>22&3C as above computes the number of bytes in the IP
header. @ makes this the new offset into the packet, which is
the start of the TCP header. The length of the TCP header
(again in 32 bit words) is the left half of byte 12 of the TCP
header. The 12>>26&3C computes this length in bytes (similar
to the IP header before). "@" makes this the new offset, which
is the start of the TCP payload. Finally, 8 reads bytes 8-12
of the payload and = checks whether the result is any of 1, 2,
5 or 8.
udp
These extensions can be used if `--protocol udp' is specified. It
provides the following options:
[!] --source-port,--sport port[:port]
Source port or port range specification. See the description
of the --source-port option of the TCP extension for details.
[!] --destination-port,--dport port[:port]
Destination port or port range specification. See the
description of the --destination-port option of the TCP
extension for details.
iptables can use extended target modules: the following are included
in the standard distribution.
AUDIT
This target allows to create audit records for packets hitting the
target. It can be used to record accepted, dropped, and rejected
packets. See auditd(8) for additional details.
--type {accept|drop|reject}
Set type of audit record.
Example:
iptables -N AUDIT_DROP
iptables -A AUDIT_DROP -j AUDIT --type drop
iptables -A AUDIT_DROP -j DROP
CHECKSUM
This target allows to selectively work around broken/old
applications. It can only be used in the mangle table.
--checksum-fill
Compute and fill in the checksum in a packet that lacks a
checksum. This is particularly useful, if you need to work
around old applications such as dhcp clients, that do not work
well with checksum offloads, but don't want to disable
checksum offload in your device.
CLASSIFY
This module allows you to set the skb->priority value (and thus
classify the packet into a specific CBQ class).
--set-class major:minor
Set the major and minor class value. The values are always
interpreted as hexadecimal even if no 0x prefix is given.
CLUSTERIP (IPv4-specific)
This module allows you to configure a simple cluster of nodes that
share a certain IP and MAC address without an explicit load balancer
in front of them. Connections are statically distributed between the
nodes in this cluster.
--new Create a new ClusterIP. You always have to set this on the
first rule for a given ClusterIP.
--hashmode mode
Specify the hashing mode. Has to be one of sourceip,
sourceip-sourceport, sourceip-sourceport-destport.
--clustermac mac
Specify the ClusterIP MAC address. Has to be a link-layer
multicast address
--total-nodes num
Number of total nodes within this cluster.
--local-node num
Local node number within this cluster.
--hash-init rnd
Specify the random seed used for hash initialization.
CONNMARK
This module sets the netfilter mark value associated with a
connection. The mark is 32 bits wide.
--set-xmark value[/mask]
Zero out the bits given by mask and XOR value into the ctmark.
--save-mark [--nfmask nfmask] [--ctmask ctmask]
Copy the packet mark (nfmark) to the connection mark (ctmark)
using the given masks. The new nfmark value is determined as
follows:
ctmark = (ctmark & ~ctmask) ^ (nfmark & nfmask)
i.e. ctmask defines what bits to clear and nfmask what bits of
the nfmark to XOR into the ctmark. ctmask and nfmask default
to 0xFFFFFFFF.
--restore-mark [--nfmask nfmask] [--ctmask ctmask]
Copy the connection mark (ctmark) to the packet mark (nfmark)
using the given masks. The new ctmark value is determined as
follows:
nfmark = (nfmark & ~nfmask) ^ (ctmark & ctmask);
i.e. nfmask defines what bits to clear and ctmask what bits of
the ctmark to XOR into the nfmark. ctmask and nfmask default
to 0xFFFFFFFF.
--restore-mark is only valid in the mangle table.
The following mnemonics are available for --set-xmark:
--and-mark bits
Binary AND the ctmark with bits. (Mnemonic for --set-xmark
0/invbits, where invbits is the binary negation of bits.)
--or-mark bits
Binary OR the ctmark with bits. (Mnemonic for --set-xmark
bits/bits.)
--xor-mark bits
Binary XOR the ctmark with bits. (Mnemonic for --set-xmark
bits/0.)
--set-mark value[/mask]
Set the connection mark. If a mask is specified then only
those bits set in the mask are modified.
--save-mark [--mask mask]
Copy the nfmark to the ctmark. If a mask is specified, only
those bits are copied.
--restore-mark [--mask mask]
Copy the ctmark to the nfmark. If a mask is specified, only
those bits are copied. This is only valid in the mangle table.
CONNSECMARK
This module copies security markings from packets to connections (if
unlabeled), and from connections back to packets (also only if
unlabeled). Typically used in conjunction with SECMARK, it is valid
in the security table (for backwards compatibility with older
kernels, it is also valid in the mangle table).
--save If the packet has a security marking, copy it to the
connection if the connection is not marked.
--restore
If the packet does not have a security marking, and the
connection does, copy the security marking from the connection
to the packet.
CT
The CT target allows to set parameters for a packet or its associated
connection. The target attaches a "template" connection tracking
entry to the packet, which is then used by the conntrack core when
initializing a new ct entry. This target is thus only valid in the
"raw" table.
--notrack
Disables connection tracking for this packet.
--helper name
Use the helper identified by name for the connection. This is
more flexible than loading the conntrack helper modules with
preset ports.
--ctevents event[,...]
Only generate the specified conntrack events for this
connection. Possible event types are: new, related, destroy,
reply, assured, protoinfo, helper, mark (this refers to the
ctmark, not nfmark), natseqinfo, secmark (ctsecmark).
--expevents event[,...]
Only generate the specified expectation events for this
connection. Possible event types are: new.
--zone-orig {id|mark}
For traffic coming from ORIGINAL direction, assign this packet
to zone id and only have lookups done in that zone. If mark is
used instead of id, the zone is derived from the packet
nfmark.
--zone-reply {id|mark}
For traffic coming from REPLY direction, assign this packet to
zone id and only have lookups done in that zone. If mark is
used instead of id, the zone is derived from the packet
nfmark.
--zone {id|mark}
Assign this packet to zone id and only have lookups done in
that zone. If mark is used instead of id, the zone is derived
from the packet nfmark. By default, packets have zone 0. This
option applies to both directions.
--timeout name
Use the timeout policy identified by name for the connection.
This is provides more flexible timeout policy definition than
global timeout values available at
/proc/sys/net/netfilter/nf_conntrack_*_timeout_*.
DNAT
This target is only valid in the nat table, in the PREROUTING and
OUTPUT chains, and user-defined chains which are only called from
those chains. It specifies that the destination address of the
packet should be modified (and all future packets in this connection
will also be mangled), and rules should cease being examined. It
takes the following options:
--to-destination [ipaddr[-ipaddr]][:port[-port]]
which can specify a single new destination IP address, an
inclusive range of IP addresses. Optionally a port range, if
the rule also specifies one of the following protocols: tcp,
udp, dccp or sctp. If no port range is specified, then the
destination port will never be modified. If no IP address is
specified then only the destination port will be modified. In
Kernels up to 2.6.10 you can add several --to-destination
options. For those kernels, if you specify more than one
destination address, either via an address range or multiple
--to-destination options, a simple round-robin (one after
another in cycle) load balancing takes place between these
addresses. Later Kernels (>= 2.6.11-rc1) don't have the
ability to NAT to multiple ranges anymore.
--random
If option --random is used then port mapping will be
randomized (kernel >= 2.6.22).
--persistent
Gives a client the same source-/destination-address for each
connection. This supersedes the SAME target. Support for
persistent mappings is available from 2.6.29-rc2.
IPv6 support available since Linux kernels >= 3.7.
DNPT (IPv6-specific)
Provides stateless destination IPv6-to-IPv6 Network Prefix
Translation (as described by RFC 6296).
You have to use this target in the mangle table, not in the nat
table. It takes the following options:
--src-pfx [prefix/length]
Set source prefix that you want to translate and length
--dst-pfx [prefix/length]
Set destination prefix that you want to use in the translation
and length
You have to use the SNPT target to undo the translation. Example:
ip6tables -t mangle -I POSTROUTING -s fd00::/64 -o vboxnet0
-j SNPT --src-pfx fd00::/64 --dst-pfx 2001:e20:2000:40f::/64
ip6tables -t mangle -I PREROUTING -i wlan0 -d
2001:e20:2000:40f::/64 -j DNPT --src-pfx
2001:e20:2000:40f::/64 --dst-pfx fd00::/64
You may need to enable IPv6 neighbor proxy:
sysctl -w net.ipv6.conf.all.proxy_ndp=1
You also have to use the NOTRACK target to disable connection
tracking for translated flows.
DSCP
This target allows to alter the value of the DSCP bits within the TOS
header of the IPv4 packet. As this manipulates a packet, it can only
be used in the mangle table.
--set-dscp value
Set the DSCP field to a numerical value (can be decimal or
hex)
--set-dscp-class class
Set the DSCP field to a DiffServ class.
ECN (IPv4-specific)
This target allows to selectively work around known ECN blackholes.
It can only be used in the mangle table.
--ecn-tcp-remove
Remove all ECN bits from the TCP header. Of course, it can
only be used in conjunction with -p tcp.
HL (IPv6-specific)
This is used to modify the Hop Limit field in IPv6 header. The Hop
Limit field is similar to what is known as TTL value in IPv4.
Setting or incrementing the Hop Limit field can potentially be very
dangerous, so it should be avoided at any cost. This target is only
valid in mangle table.
Don't ever set or increment the value on packets that leave your
local network!
--hl-set value
Set the Hop Limit to `value'.
--hl-dec value
Decrement the Hop Limit `value' times.
--hl-inc value
Increment the Hop Limit `value' times.
HMARK
Like MARK, i.e. set the fwmark, but the mark is calculated from
hashing packet selector at choice. You have also to specify the mark
range and, optionally, the offset to start from. ICMP error messages
are inspected and used to calculate the hashing.
Existing options are:
--hmark-tuple tuple
Possible tuple members are: src meaning source address (IPv4,
IPv6 address), dst meaning destination address (IPv4, IPv6
address), sport meaning source port (TCP, UDP, UDPlite, SCTP,
DCCP), dport meaning destination port (TCP, UDP, UDPlite,
SCTP, DCCP), spi meaning Security Parameter Index (AH, ESP),
and ct meaning the usage of the conntrack tuple instead of the
packet selectors.
--hmark-mod value (must be > 0)
Modulus for hash calculation (to limit the range of possible
marks)
--hmark-offset value
Offset to start marks from.
For advanced usage, instead of using --hmark-tuple, you can specify
custom
prefixes and masks:
--hmark-src-prefix cidr
The source address mask in CIDR notation.
--hmark-dst-prefix cidr
The destination address mask in CIDR notation.
--hmark-sport-mask value
A 16 bit source port mask in hexadecimal.
--hmark-dport-mask value
A 16 bit destination port mask in hexadecimal.
--hmark-spi-mask value
A 32 bit field with spi mask.
--hmark-proto-mask value
An 8 bit field with layer 4 protocol number.
--hmark-rnd value
A 32 bit random custom value to feed hash calculation.
Examples:
iptables -t mangle -A PREROUTING -m conntrack --ctstate NEW
-j HMARK --hmark-tuple ct,src,dst,proto --hmark-offset 10000
--hmark-mod 10 --hmark-rnd 0xfeedcafe
iptables -t mangle -A PREROUTING -j HMARK --hmark-offset 10000
--hmark-tuple src,dst,proto --hmark-mod 10 --hmark-rnd 0xdeafbeef
IDLETIMER
This target can be used to identify when interfaces have been idle
for a certain period of time. Timers are identified by labels and
are created when a rule is set with a new label. The rules also take
a timeout value (in seconds) as an option. If more than one rule
uses the same timer label, the timer will be restarted whenever any
of the rules get a hit. One entry for each timer is created in
sysfs. This attribute contains the timer remaining for the timer to
expire. The attributes are located under the xt_idletimer class:
/sys/class/xt_idletimer/timers/<label>
When the timer expires, the target module sends a sysfs notification
to the userspace, which can then decide what to do (eg. disconnect to
save power).
--timeout amount
This is the time in seconds that will trigger the
notification.
--label string
This is a unique identifier for the timer. The maximum length
for the label string is 27 characters.
LED
This creates an LED-trigger that can then be attached to system
indicator lights, to blink or illuminate them when certain packets
pass through the system. One example might be to light up an LED for
a few minutes every time an SSH connection is made to the local
machine. The following options control the trigger behavior:
--led-trigger-id name
This is the name given to the LED trigger. The actual name of
the trigger will be prefixed with "netfilter-".
--led-delay ms
This indicates how long (in milliseconds) the LED should be
left illuminated when a packet arrives before being switched
off again. The default is 0 (blink as fast as possible.) The
special value inf can be given to leave the LED on permanently
once activated. (In this case the trigger will need to be
manually detached and reattached to the LED device to switch
it off again.)
--led-always-blink
Always make the LED blink on packet arrival, even if the LED
is already on. This allows notification of new packets even
with long delay values (which otherwise would result in a
silent prolonging of the delay time.)
Example:
Create an LED trigger for incoming SSH traffic:
iptables -A INPUT -p tcp --dport 22 -j LED --led-trigger-id
ssh
Then attach the new trigger to an LED:
echo netfilter-ssh >/sys/class/leds/ledname/trigger
LOG
Turn on kernel logging of matching packets. When this option is set
for a rule, the Linux kernel will print some information on all
matching packets (like most IP/IPv6 header fields) via the kernel log
(where it can be read with dmesg(1) or read in the syslog).
This is a "non-terminating target", i.e. rule traversal continues at
the next rule. So if you want to LOG the packets you refuse, use two
separate rules with the same matching criteria, first using target
LOG then DROP (or REJECT).
--log-level level
Level of logging, which can be (system-specific) numeric or a
mnemonic. Possible values are (in decreasing order of
priority): emerg, alert, crit, error, warning, notice, info or
debug.
--log-prefix prefix
Prefix log messages with the specified prefix; up to 29
letters long, and useful for distinguishing messages in the
logs.
--log-tcp-sequence
Log TCP sequence numbers. This is a security risk if the log
is readable by users.
--log-tcp-options
Log options from the TCP packet header.
--log-ip-options
Log options from the IP/IPv6 packet header.
--log-uid
Log the userid of the process which generated the packet.
MARK
This target is used to set the Netfilter mark value associated with
the packet. It can, for example, be used in conjunction with routing
based on fwmark (needs iproute2). If you plan on doing so, note that
the mark needs to be set in the PREROUTING chain of the mangle table
to affect routing. The mark field is 32 bits wide.
--set-xmark value[/mask]
Zeroes out the bits given by mask and XORs value into the
packet mark ("nfmark"). If mask is omitted, 0xFFFFFFFF is
assumed.
--set-mark value[/mask]
Zeroes out the bits given by mask and ORs value into the
packet mark. If mask is omitted, 0xFFFFFFFF is assumed.
The following mnemonics are available:
--and-mark bits
Binary AND the nfmark with bits. (Mnemonic for --set-xmark
0/invbits, where invbits is the binary negation of bits.)
--or-mark bits
Binary OR the nfmark with bits. (Mnemonic for --set-xmark
bits/bits.)
--xor-mark bits
Binary XOR the nfmark with bits. (Mnemonic for --set-xmark
bits/0.)
MASQUERADE
This target is only valid in the nat table, in the POSTROUTING chain.
It should only be used with dynamically assigned IP (dialup)
connections: if you have a static IP address, you should use the SNAT
target. Masquerading is equivalent to specifying a mapping to the IP
address of the interface the packet is going out, but also has the
effect that connections are forgotten when the interface goes down.
This is the correct behavior when the next dialup is unlikely to have
the same interface address (and hence any established connections are
lost anyway).
--to-ports port[-port]
This specifies a range of source ports to use, overriding the
default SNAT source port-selection heuristics (see above).
This is only valid if the rule also specifies one of the
following protocols: tcp, udp, dccp or sctp.
--random
Randomize source port mapping If option --random is used then
port mapping will be randomized (kernel >= 2.6.21).
--random-fully
Full randomize source port mapping If option --random-fully is
used then port mapping will be fully randomized (kernel >=
3.13).
IPv6 support available since Linux kernels >= 3.7.
NETMAP
This target allows you to statically map a whole network of addresses
onto another network of addresses. It can only be used from rules in
the nat table.
--to address[/mask]
Network address to map to. The resulting address will be
constructed in the following way: All 'one' bits in the mask
are filled in from the new `address'. All bits that are zero
in the mask are filled in from the original address.
IPv6 support available since Linux kernels >= 3.7.
NFLOG
This target provides logging of matching packets. When this target is
set for a rule, the Linux kernel will pass the packet to the loaded
logging backend to log the packet. This is usually used in
combination with nfnetlink_log as logging backend, which will
multicast the packet through a netlink socket to the specified
multicast group. One or more userspace processes may subscribe to the
group to receive the packets. Like LOG, this is a non-terminating
target, i.e. rule traversal continues at the next rule.
--nflog-group nlgroup
The netlink group (0 - 2^16-1) to which packets are (only
applicable for nfnetlink_log). The default value is 0.
--nflog-prefix prefix
A prefix string to include in the log message, up to 64
characters long, useful for distinguishing messages in the
logs.
--nflog-range size
This option has never worked, use --nflog-size instead
--nflog-size size
The number of bytes to be copied to userspace (only applicable
for nfnetlink_log). nfnetlink_log instances may specify their
own range, this option overrides it.
--nflog-threshold size
Number of packets to queue inside the kernel before sending
them to userspace (only applicable for nfnetlink_log). Higher
values result in less overhead per packet, but increase delay
until the packets reach userspace. The default value is 1.
NFQUEUE
This target passes the packet to userspace using the nfnetlink_queue
handler. The packet is put into the queue identified by its 16-bit
queue number. Userspace can inspect and modify the packet if
desired. Userspace must then drop or reinject the packet into the
kernel. Please see libnetfilter_queue for details. nfnetlink_queue
was added in Linux 2.6.14. The queue-balance option was added in
Linux 2.6.31, queue-bypass in 2.6.39.
--queue-num value
This specifies the QUEUE number to use. Valid queue numbers
are 0 to 65535. The default value is 0.
--queue-balance value:value
This specifies a range of queues to use. Packets are then
balanced across the given queues. This is useful for
multicore systems: start multiple instances of the userspace
program on queues x, x+1, .. x+n and use "--queue-balance
x:x+n". Packets belonging to the same connection are put into
the same nfqueue.
--queue-bypass
By default, if no userspace program is listening on an
NFQUEUE, then all packets that are to be queued are dropped.
When this option is used, the NFQUEUE rule behaves like ACCEPT
instead, and the packet will move on to the next table.
--queue-cpu-fanout
Available starting Linux kernel 3.10. When used together with
--queue-balance this will use the CPU ID as an index to map
packets to the queues. The idea is that you can improve
performance if there's a queue per CPU. This requires --queue-
balance to be specified.
NOTRACK
This extension disables connection tracking for all packets matching
that rule. It is equivalent with -j CT --notrack. Like CT, NOTRACK
can only be used in the raw table.
RATEEST
The RATEEST target collects statistics, performs rate estimation
calculation and saves the results for later evaluation using the
rateest match.
--rateest-name name
Count matched packets into the pool referred to by name, which
is freely choosable.
--rateest-interval amount{s|ms|us}
Rate measurement interval, in seconds, milliseconds or
microseconds.
--rateest-ewmalog value
Rate measurement averaging time constant.
REDIRECT
This target is only valid in the nat table, in the PREROUTING and
OUTPUT chains, and user-defined chains which are only called from
those chains. It redirects the packet to the machine itself by
changing the destination IP to the primary address of the incoming
interface (locally-generated packets are mapped to the localhost
address, 127.0.0.1 for IPv4 and ::1 for IPv6).
--to-ports port[-port]
This specifies a destination port or range of ports to use:
without this, the destination port is never altered. This is
only valid if the rule also specifies one of the following
protocols: tcp, udp, dccp or sctp.
--random
If option --random is used then port mapping will be
randomized (kernel >= 2.6.22).
IPv6 support available starting Linux kernels >= 3.7.
REJECT (IPv6-specific)
This is used to send back an error packet in response to the matched
packet: otherwise it is equivalent to DROP so it is a terminating
TARGET, ending rule traversal. This target is only valid in the
INPUT, FORWARD and OUTPUT chains, and user-defined chains which are
only called from those chains. The following option controls the
nature of the error packet returned:
--reject-with type
The type given can be icmp6-no-route, no-route,
icmp6-adm-prohibited, adm-prohibited, icmp6-addr-unreachable,
addr-unreach, or icmp6-port-unreachable, which return the
appropriate ICMPv6 error message (icmp6-port-unreachable is
the default). Finally, the option tcp-reset can be used on
rules which only match the TCP protocol: this causes a TCP RST
packet to be sent back. This is mainly useful for blocking
ident (113/tcp) probes which frequently occur when sending
mail to broken mail hosts (which won't accept your mail
otherwise). tcp-reset can only be used with kernel versions
2.6.14 or later.
REJECT (IPv4-specific)
This is used to send back an error packet in response to the matched
packet: otherwise it is equivalent to DROP so it is a terminating
TARGET, ending rule traversal. This target is only valid in the
INPUT, FORWARD and OUTPUT chains, and user-defined chains which are
only called from those chains. The following option controls the
nature of the error packet returned:
--reject-with type
The type given can be icmp-net-unreachable,
icmp-host-unreachable, icmp-port-unreachable,
icmp-proto-unreachable, icmp-net-prohibited,
icmp-host-prohibited, or icmp-admin-prohibited (*), which
return the appropriate ICMP error message
(icmp-port-unreachable is the default). The option tcp-reset
can be used on rules which only match the TCP protocol: this
causes a TCP RST packet to be sent back. This is mainly
useful for blocking ident (113/tcp) probes which frequently
occur when sending mail to broken mail hosts (which won't
accept your mail otherwise).
(*) Using icmp-admin-prohibited with kernels that do not
support it will result in a plain DROP instead of REJECT
SECMARK
This is used to set the security mark value associated with the
packet for use by security subsystems such as SELinux. It is valid
in the security table (for backwards compatibility with older
kernels, it is also valid in the mangle table). The mark is 32 bits
wide.
--selctx security_context
SET
This module adds and/or deletes entries from IP sets which can be
defined by ipset(8).
--add-set setname flag[,flag...]
add the address(es)/port(s) of the packet to the set
--del-set setname flag[,flag...]
delete the address(es)/port(s) of the packet from the set
--map-set setname flag[,flag...]
[--map-mark] [--map-prio] [--map-queue] map packet properties
(firewall mark, tc priority, hardware queue)
where flag(s) are src and/or dst specifications and there can
be no more than six of them.
--timeout value
when adding an entry, the timeout value to use instead of the
default one from the set definition
--exist
when adding an entry if it already exists, reset the timeout
value to the specified one or to the default from the set
definition
--map-set set-name
the set-name should be created with --skbinfo option
--map-mark map firewall mark to packet by lookup of value in
the set --map-prio map traffic control priority to packet by
lookup of value in the set --map-queue map hardware NIC queue
to packet by lookup of value in the set
The --map-set option can be used from the mangle table only.
The --map-prio and --map-queue flags can be used in the
OUTPUT, FORWARD and POSTROUTING chains.
Use of -j SET requires that ipset kernel support is provided, which,
for standard kernels, is the case since Linux 2.6.39.
SNAT
This target is only valid in the nat table, in the POSTROUTING and
INPUT chains, and user-defined chains which are only called from
those chains. It specifies that the source address of the packet
should be modified (and all future packets in this connection will
also be mangled), and rules should cease being examined. It takes
the following options:
--to-source [ipaddr[-ipaddr]][:port[-port]]
which can specify a single new source IP address, an inclusive
range of IP addresses. Optionally a port range, if the rule
also specifies one of the following protocols: tcp, udp, dccp
or sctp. If no port range is specified, then source ports
below 512 will be mapped to other ports below 512: those
between 512 and 1023 inclusive will be mapped to ports below
1024, and other ports will be mapped to 1024 or above. Where
possible, no port alteration will occur. In Kernels up to
2.6.10, you can add several --to-source options. For those
kernels, if you specify more than one source address, either
via an address range or multiple --to-source options, a simple
round-robin (one after another in cycle) takes place between
these addresses. Later Kernels (>= 2.6.11-rc1) don't have the
ability to NAT to multiple ranges anymore.
--random
If option --random is used then port mapping will be
randomized through a hash-based algorithm (kernel >= 2.6.21).
--random-fully
If option --random-fully is used then port mapping will be
fully randomized through a PRNG (kernel >= 3.14).
--persistent
Gives a client the same source-/destination-address for each
connection. This supersedes the SAME target. Support for
persistent mappings is available from 2.6.29-rc2.
Kernels prior to 2.6.36-rc1 don't have the ability to SNAT in the
INPUT chain.
IPv6 support available since Linux kernels >= 3.7.
SNPT (IPv6-specific)
Provides stateless source IPv6-to-IPv6 Network Prefix Translation (as
described by RFC 6296).
You have to use this target in the mangle table, not in the nat
table. It takes the following options:
--src-pfx [prefix/length]
Set source prefix that you want to translate and length
--dst-pfx [prefix/length]
Set destination prefix that you want to use in the translation
and length
You have to use the DNPT target to undo the translation. Example:
ip6tables -t mangle -I POSTROUTING -s fd00::/64 -o vboxnet0
-j SNPT --src-pfx fd00::/64 --dst-pfx 2001:e20:2000:40f::/64
ip6tables -t mangle -I PREROUTING -i wlan0 -d
2001:e20:2000:40f::/64 -j DNPT --src-pfx
2001:e20:2000:40f::/64 --dst-pfx fd00::/64
You may need to enable IPv6 neighbor proxy:
sysctl -w net.ipv6.conf.all.proxy_ndp=1
You also have to use the NOTRACK target to disable connection
tracking for translated flows.
SYNPROXY
This target will process TCP three-way-handshake parallel in
netfilter context to protect either local or backend system. This
target requires connection tracking because sequence numbers need to
be translated.
--mss maximum segment size
Maximum segment size announced to clients. This must match the
backend.
--wscale window scale
Window scale announced to clients. This must match the
backend.
--sack-perm
Pass client selective acknowledgement option to backend (will
be disabled if not present).
--timestamps
Pass client timestamp option to backend (will be disabled if
not present, also needed for selective acknowledgement and
window scaling).
Example:
Determine tcp options used by backend, from an external system
tcpdump -pni eth0 -c 1 'tcp[tcpflags] == (tcp-syn|tcp-ack)'
port 80 &
telnet 192.0.2.42 80
18:57:24.693307 IP 192.0.2.42.80 > 192.0.2.43.48757:
Flags [S.], seq 360414582, ack 788841994, win 14480,
options [mss 1460,sackOK,
TS val 1409056151 ecr 9690221,
nop,wscale 9],
length 0
Switch tcp_loose mode off, so conntrack will mark out-of-flow packets
as state INVALID.
echo 0 > /proc/sys/net/netfilter/nf_conntrack_tcp_loose
Make SYN packets untracked
iptables -t raw -A PREROUTING -i eth0 -p tcp --dport 80
--syn -j CT --notrack
Catch UNTRACKED (SYN packets) and INVALID (3WHS ACK packets) states
and send them to SYNPROXY. This rule will respond to SYN packets with
SYN+ACK syncookies, create ESTABLISHED for valid client response
(3WHS ACK packets) and drop incorrect cookies. Flags combinations not
expected during 3WHS will not match and continue (e.g. SYN+FIN,
SYN+ACK).
iptables -A INPUT -i eth0 -p tcp --dport 80
-m state --state UNTRACKED,INVALID -j SYNPROXY
--sack-perm --timestamp --mss 1460 --wscale 9
Drop invalid packets, this will be out-of-flow packets that were not
matched by SYNPROXY.
iptables -A INPUT -i eth0 -p tcp --dport 80 -m state --state
INVALID -j DROP
TCPMSS
This target allows to alter the MSS value of TCP SYN packets, to
control the maximum size for that connection (usually limiting it to
your outgoing interface's MTU minus 40 for IPv4 or 60 for IPv6,
respectively). Of course, it can only be used in conjunction with -p
tcp.
This target is used to overcome criminally braindead ISPs or servers
which block "ICMP Fragmentation Needed" or "ICMPv6 Packet Too Big"
packets. The symptoms of this problem are that everything works fine
from your Linux firewall/router, but machines behind it can never
exchange large packets:
1. Web browsers connect, then hang with no data received.
2. Small mail works fine, but large emails hang.
3. ssh works fine, but scp hangs after initial handshaking.
Workaround: activate this option and add a rule to your firewall
configuration like:
iptables -t mangle -A FORWARD -p tcp --tcp-flags SYN,RST SYN
-j TCPMSS --clamp-mss-to-pmtu
--set-mss value
Explicitly sets MSS option to specified value. If the MSS of
the packet is already lower than value, it will not be
increased (from Linux 2.6.25 onwards) to avoid more problems
with hosts relying on a proper MSS.
--clamp-mss-to-pmtu
Automatically clamp MSS value to (path_MTU - 40 for IPv4; -60
for IPv6). This may not function as desired where asymmetric
routes with differing path MTU exist — the kernel uses the
path MTU which it would use to send packets from itself to the
source and destination IP addresses. Prior to Linux 2.6.25,
only the path MTU to the destination IP address was considered
by this option; subsequent kernels also consider the path MTU
to the source IP address.
These options are mutually exclusive.
TCPOPTSTRIP
This target will strip TCP options off a TCP packet. (It will
actually replace them by NO-OPs.) As such, you will need to add the
-p tcp parameters.
--strip-options option[,option...]
Strip the given option(s). The options may be specified by TCP
option number or by symbolic name. The list of recognized
options can be obtained by calling iptables with -j
TCPOPTSTRIP -h.
TEE
The TEE target will clone a packet and redirect this clone to another
machine on the local network segment. In other words, the nexthop
must be the target, or you will have to configure the nexthop to
forward it further if so desired.
--gateway ipaddr
Send the cloned packet to the host reachable at the given IP
address. Use of 0.0.0.0 (for IPv4 packets) or :: (IPv6) is
invalid.
To forward all incoming traffic on eth0 to an Network Layer logging
box:
-t mangle -A PREROUTING -i eth0 -j TEE --gateway 2001:db8::1
TOS
This module sets the Type of Service field in the IPv4 header
(including the "precedence" bits) or the Priority field in the IPv6
header. Note that TOS shares the same bits as DSCP and ECN. The TOS
target is only valid in the mangle table.
--set-tos value[/mask]
Zeroes out the bits given by mask (see NOTE below) and XORs
value into the TOS/Priority field. If mask is omitted, 0xFF is
assumed.
--set-tos symbol
You can specify a symbolic name when using the TOS target for
IPv4. It implies a mask of 0xFF (see NOTE below). The list of
recognized TOS names can be obtained by calling iptables with
-j TOS -h.
The following mnemonics are available:
--and-tos bits
Binary AND the TOS value with bits. (Mnemonic for --set-tos
0/invbits, where invbits is the binary negation of bits. See
NOTE below.)
--or-tos bits
Binary OR the TOS value with bits. (Mnemonic for --set-tos
bits/bits. See NOTE below.)
--xor-tos bits
Binary XOR the TOS value with bits. (Mnemonic for --set-tos
bits/0. See NOTE below.)
NOTE: In Linux kernels up to and including 2.6.38, with the exception
of longterm releases 2.6.32 (>=.42), 2.6.33 (>=.15), and 2.6.35
(>=.14), there is a bug whereby IPv6 TOS mangling does not behave as
documented and differs from the IPv4 version. The TOS mask indicates
the bits one wants to zero out, so it needs to be inverted before
applying it to the original TOS field. However, the aformentioned
kernels forgo the inversion which breaks --set-tos and its mnemonics.
TPROXY
This target is only valid in the mangle table, in the PREROUTING
chain and user-defined chains which are only called from this chain.
It redirects the packet to a local socket without changing the packet
header in any way. It can also change the mark value which can then
be used in advanced routing rules. It takes three options:
--on-port port
This specifies a destination port to use. It is a required
option, 0 means the new destination port is the same as the
original. This is only valid if the rule also specifies -p tcp
or -p udp.
--on-ip address
This specifies a destination address to use. By default the
address is the IP address of the incoming interface. This is
only valid if the rule also specifies -p tcp or -p udp.
--tproxy-mark value[/mask]
Marks packets with the given value/mask. The fwmark value set
here can be used by advanced routing. (Required for
transparent proxying to work: otherwise these packets will get
forwarded, which is probably not what you want.)
TRACE
This target marks packets so that the kernel will log every rule
which match the packets as those traverse the tables, chains, rules.
A logging backend, such as ip(6)t_LOG or nfnetlink_log, must be
loaded for this to be visible. The packets are logged with the
string prefix: "TRACE: tablename:chainname:type:rulenum " where type
can be "rule" for plain rule, "return" for implicit rule at the end
of a user defined chain and "policy" for the policy of the built in
chains.
It can only be used in the raw table.
TTL (IPv4-specific)
This is used to modify the IPv4 TTL header field. The TTL field
determines how many hops (routers) a packet can traverse until it's
time to live is exceeded.
Setting or incrementing the TTL field can potentially be very
dangerous, so it should be avoided at any cost. This target is only
valid in mangle table.
Don't ever set or increment the value on packets that leave your
local network!
--ttl-set value
Set the TTL value to `value'.
--ttl-dec value
Decrement the TTL value `value' times.
--ttl-inc value
Increment the TTL value `value' times.
ULOG (IPv4-specific)
This is the deprecated ipv4-only predecessor of the NFLOG target. It
provides userspace logging of matching packets. When this target is
set for a rule, the Linux kernel will multicast this packet through a
netlink socket. One or more userspace processes may then subscribe to
various multicast groups and receive the packets. Like LOG, this is
a "non-terminating target", i.e. rule traversal continues at the next
rule.
--ulog-nlgroup nlgroup
This specifies the netlink group (1-32) to which the packet is
sent. Default value is 1.
--ulog-prefix prefix
Prefix log messages with the specified prefix; up to 32
characters long, and useful for distinguishing messages in the
logs.
--ulog-cprange size
Number of bytes to be copied to userspace. A value of 0
always copies the entire packet, regardless of its size.
Default is 0.
--ulog-qthreshold size
Number of packet to queue inside kernel. Setting this value
to, e.g. 10 accumulates ten packets inside the kernel and
transmits them as one netlink multipart message to userspace.
Default is 1 (for backwards compatibility).
This page is part of the iptables (administer and maintain packet
filter rules) project. Information about the project can be found at
⟨http://www.netfilter.org/⟩. If you have a bug report for this man‐
ual page, see ⟨http://bugzilla.netfilter.org/⟩. This page was
obtained from the project's upstream Git repository
⟨http://bugzilla.netfilter.org/⟩ on 2018-02-02. (At that time, the
date of the most recent commit that was found in the repository was
2018-01-31.) If you discover any rendering problems in this HTML
version of the page, or you believe there is a better or more up-to-
date source for the page, or you have corrections or improvements to
the information in this COLOPHON (which is not part of the original
manual page), send a mail to man-pages@man7.org
iptables 1.6.1 iptables-extensions(8)
Pages that refer to this page: proc(5), iptables(8), tc-fw(8), tc-xt(8)
|
HTML rendering created 2018-02-02 by Michael Kerrisk, author of The Linux Programming Interface, maintainer of the Linux man-pages project. For details of in-depth Linux/UNIX system programming training courses that I teach, look here. Hosting by jambit GmbH.
|
|