|
NAME | SYNOPSIS | DESCRIPTION | VERSIONS | NOTES | SEE ALSO | COLOPHON |
|
SLABINFO(5) Linux Programmer's Manual SLABINFO(5)
slabinfo - kernel slab allocator statistics
cat /proc/slabinfo
Frequently used objects in the Linux kernel (buffer heads, inodes,
dentries, etc.) have their own cache. The file /proc/slabinfo gives
statistics on these caches. The following (edited) output shows an
example of the contents of this file:
$ sudo cat /proc/slabinfo
slabinfo - version: 2.1
# name <active_objs> <num_objs> <objsize> <objperslab> <pagesperslab> ...
sigqueue 100 100 160 25 1 : tunables 0 0 0 : slabdata 4 4 0
sighand_cache 355 405 2112 15 8 : tunables 0 0 0 : slabdata 27 27 0
kmalloc-8192 96 96 8192 4 8 : tunables 0 0 0 : slabdata 24 24 0
...
The first line of output includes a version number, which allows an
application that is reading the file to handle changes in the file
format. (See VERSIONS, below.) The next line lists the names of the
columns in the remaining lines.
Each of the remaining lines displays information about a specified
cache. Following the cache name, the output shown in each line shows
three components for each cache:
* statistics
* tunables
* slabdata
The statistics are as follows:
active_objs
The number of objects that are currently active (i.e., in
use).
num_objs
The total number of allocated objects (i.e., objects that are
both in use and not in use).
objsize
The size of objects in this slab, in bytes.
objperslab
The number of objects stored in each slab.
pagesperslab
The number of pages allocated for each slab.
The tunables entries in each line show tunable parameters for the
corresponding cache. When using the default SLUB allocator, there
are no tunables, the /proc/slabinfo file is not writable, and the
value 0 is shown in these fields. When using the older SLAB alloca‐
tor, the tunables for a particular cache can be set by writing lines
of the following form to /proc/slabinfo:
# echo 'name limit batchcount sharedfactor' > /proc/slabinfo
Here, name is the cache name, and limit, batchcount, and sharedfactor
are integers defining new values for the corresponding tunables. The
limit value should be a positive value, batchcount should be a posi‐
tive value that is less than or equal to limit, and sharedfactor
should be nonnegative. If any of the specified values is invalid,
the cache settings are left unchanged.
The tunables entries in each line contain the following fields:
limit The maximum number of objects that will be cached.
batchcount
On SMP systems, this specifies the number of objects to trans‐
fer at one time when refilling the available object list.
sharedfactor
[To be documented]
The slabdata entries in each line contain the following fields:
active_slabs
The number of active slabs.
nums_slabs
The total number of slabs.
sharedavail
[To be documented]
Note that because of object alignment and slab cache overhead,
objects are not normally packed tightly into pages. Pages with even
one in-use object are considered in-use and cannot be freed.
Kernels configured with CONFIG_DEBUG_SLAB will also have additional
statistics fields in each line, and the first line of the file will
contain the string "(statistics)". The statistics field include :
the high water mark of active objects; the number of times objects
have been allocated; the number of times the cache has grown (new
pages added to this cache); the number of times the cache has been
reaped (unused pages removed from this cache); and the number of
times there was an error allocating new pages to this cache.
The /proc/slabinfo file first appeared in Linux 2.1.23. The file is
versioned, and over time there have been a number of versions with
different layouts:
1.0 Present throughout the Linux 2.2.x kernel series.
1.1 Present in the Linux 2.4.x kernel series.
1.2 A format that was briefly present in the Linux 2.5 development
series.
2.0 Present in Linux 2.6.x kernels up to and including Linux
2.6.9.
2.1 The current format, which first appeared in Linux 2.6.10.
Only root can read and (if the kernel was configured with
CONFIG_SLAB) write the /proc/slabinfo file.
The total amount of memory allocated to the SLAB/SLUB cache is shown
in the Slab field of /proc/meminfo.
slabtop(1)
The kernel source file Documentation/vm/slub.txt and
tools/vm/slabinfo.c.
This page is part of release 4.15 of the Linux man-pages project. A
description of the project, information about reporting bugs, and the
latest version of this page, can be found at
https://www.kernel.org/doc/man-pages/.
2017-09-15 SLABINFO(5)
Pages that refer to this page: proc(5)
Copyright and license for this manual page
|
HTML rendering created 2018-02-02 by Michael Kerrisk, author of The Linux Programming Interface, maintainer of the Linux man-pages project. For details of in-depth Linux/UNIX system programming training courses that I teach, look here. Hosting by jambit GmbH.
|
|