/*
 * This file is part of the coreboot project.
 *
 * Copyright (C) 2014 - 2017 Intel Corporation.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; version 2 of the License.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 */

#ifndef _DENVERTON_NS_GPIO_H_
#define _DENVERTON_NS_GPIO_H_

#define RShiftU64(Operand, Count) (Operand >> Count)
#define LShiftU64(Operand, Count) (Operand << Count)

#include <soc/gpio_defs.h>

#ifndef __ACPI__
#include <stdint.h>
#include <stddef.h>

//
// Structure for storing information about registers offset, community,
// maximal pad number for available groups
//
struct GPIO_GROUP_INFO {
	uint32_t Community;
	uint32_t PadOwnOffset;
	uint32_t HostOwnOffset;
	uint32_t GpiIsOffset;
	uint32_t GpiIeOffset;
	uint32_t GpiGpeStsOffset;
	uint32_t GpiGpeEnOffset;
	uint32_t SmiStsOffset;
	uint32_t SmiEnOffset;
	uint32_t NmiStsOffset;
	uint32_t NmiEnOffset;
	uint32_t PadCfgLockOffset;
	uint32_t PadCfgLockTxOffset;
	uint32_t PadCfgOffset;
	uint32_t PadPerGroup;
};

//
// If in GPIO_GROUP_INFO structure certain register doesn't exist
// it will have value equal to NO_REGISTER_FOR_PROPERTY
//
#define NO_REGISTER_FOR_PROPERTY (~0u)

//
// Below defines are based on GPIO_CONFIG structure fields
//
#define GPIO_CONF_PAD_MODE_MASK 0xF
#define GPIO_CONF_PAD_MODE_BIT_POS 0
#define GPIO_CONF_HOST_OWN_MASK 0x3
#define GPIO_CONF_HOST_OWN_BIT_POS 0
#define GPIO_CONF_DIR_MASK 0x7
#define GPIO_CONF_DIR_BIT_POS 0
#define GPIO_CONF_INV_MASK 0x18
#define GPIO_CONF_INV_BIT_POS 3
#define GPIO_CONF_OUTPUT_MASK 0x3
#define GPIO_CONF_OUTPUT_BIT_POS 0
#define GPIO_CONF_INT_ROUTE_MASK 0x1F
#define GPIO_CONF_INT_ROUTE_BIT_POS 0
#define GPIO_CONF_INT_TRIG_MASK 0xE0
#define GPIO_CONF_INT_TRIG_BIT_POS 5
#define GPIO_CONF_RESET_MASK 0x7
#define GPIO_CONF_RESET_BIT_POS 0
#define GPIO_CONF_TERM_MASK 0x1F
#define GPIO_CONF_TERM_BIT_POS 0
#define GPIO_CONF_PADTOL_MASK 0x60
#define GPIO_CONF_PADTOL_BIT_POS 5
#define GPIO_CONF_LOCK_MASK 0x7
#define GPIO_CONF_LOCK_BIT_POS 0
#define GPIO_CONF_RXRAW_MASK 0x3
#define GPIO_CONF_RXRAW_BIT_POS 0

/**
GPIO configuration structure used for pin programming.
Structure contains fields that can be used to configure pad.
**/
struct GPIO_CONFIG {
	/**
	Pad Mode
	Pad can be set as GPIO or one of its native functions.
	When in native mode setting Direction (except Inversion), OutputState,
	InterruptConfig and Host Software Pad Ownership are unnecessary.
	Refer to definition of GPIO_PAD_MODE.
	Refer to EDS for each native mode according to the pad.
	**/
	uint32_t PadMode : 4;
	/**
	Host Software Pad Ownership
	Set pad to ACPI mode or GPIO Driver Mode.
	Refer to definition of GPIO_HOSTSW_OWN.
	**/
	uint32_t HostSoftPadOwn : 2;
	/**
	GPIO Direction
	Can choose between In, In with inversion Out, both In and Out, both In
	with inversion and out or disabling both.
	Refer to definition of GPIO_DIRECTION for supported settings.
	**/
	uint32_t Direction : 5;
	/**
	Output State
	Set Pad output value.
	Refer to definition of GPIO_OUTPUT_STATE for supported settings.
	This setting takes place when output is enabled.
	**/
	uint32_t OutputState : 2;
	/**
	GPIO Interrupt Configuration
	Set Pad to cause one of interrupts (IOxAPIC/SCI/SMI/NMI). This setting
	is applicable only if GPIO is in input mode.
	If GPIO is set to cause an SCI then also Gpe is enabled for this pad.
	Refer to definition of GPIO_INT_CONFIG for supported settings.
	**/
	uint32_t InterruptConfig : 8;
	/**
	GPIO Power Configuration.
	This setting controls Pad Reset Configuration.
	Refer to definition of GPIO_RESET_CONFIG for supported settings.
	**/
	uint32_t PowerConfig : 4;

	/**
	GPIO Electrical Configuration
	This setting controls pads termination and voltage tolerance.
	Refer to definition of GPIO_ELECTRICAL_CONFIG for supported settings.
	**/
	uint32_t ElectricalConfig : 7;

	/**
	GPIO Lock Configuration
	This setting controls pads lock.
	Refer to definition of GPIO_LOCK_CONFIG for supported settings.
	**/
	uint32_t LockConfig : 3;
	/**
	Additional GPIO configuration
	Refer to definition of GPIO_OTHER_CONFIG for supported settings.
	**/
	uint32_t OtherSettings : 2;
	uint32_t RsvdBits : 27; ///< Reserved bits for future extension
} __attribute__((packed));

typedef enum { GpioHardwareDefault = 0x0 } GPIO_HARDWARE_DEFAULT;

///
/// GPIO Pad Mode
///
typedef enum {
	GpioPadModeGpio = 0x1,
	GpioPadModeNative1 = 0x3,
	GpioPadModeNative2 = 0x5,
	GpioPadModeNative3 = 0x7,
	GpioPadModeNative4 = 0x9
} GPIO_PAD_MODE;

///
/// Host Software Pad Ownership modes
///
typedef enum {
	GpioHostOwnDefault = 0x0, ///< Leave ownership value unmodified
	GpioHostOwnAcpi = 0x1,    ///< Set HOST ownership to ACPI
	GpioHostOwnGpio = 0x3     ///< Set HOST ownership to GPIO
} GPIO_HOSTSW_OWN;

///
/// GPIO Direction
///
typedef enum {
	GpioDirDefault = 0x0, ///< Leave pad direction setting unmodified
	GpioDirInOut =
		(0x1 | (0x1 << 3)), ///< Set pad for both output and input
	GpioDirInInvOut = (0x1 | (0x3 << 3)), ///< Set pad for both output and
					      ///input with inversion
	GpioDirIn = (0x3 | (0x1 << 3)),       ///< Set pad for input only
	GpioDirInInv = (0x3 | (0x3 << 3)), ///< Set pad for input with inversion
	GpioDirOut = 0x5,		   ///< Set pad for output only
	GpioDirNone = 0x7		   ///< Disable both output and input
} GPIO_DIRECTION;

///
/// GPIO Output State
///
typedef enum {
	GpioOutDefault = 0x0, ///< Leave output value unmodified
	GpioOutLow = 0x1,     ///< Set output to low
	GpioOutHigh = 0x3     ///< Set output to high
} GPIO_OUTPUT_STATE;

///
/// GPIO interrupt configuration
/// This setting is applicable only if GPIO is in input mode.
/// GPIO_INT_CONFIG allows to choose which interrupt is generated
/// (IOxAPIC/SCI/SMI/NMI)
/// and how it is triggered (edge or level).
/// Field from GpioIntNmi to GpioIntApic can be OR'ed with GpioIntLevel to
/// GpioIntBothEdgecan
/// to describe an interrupt e.g. GpioIntApic | GpioIntLevel
/// If GPIO is set to cause an SCI then also Gpe is enabled for this pad.
/// Not all GPIO are capable of generating an SMI or NMI interrupt
///

typedef enum {
	GpioIntDefault = 0x0, ///< Leave value of interrupt routing unmodified
	GpioIntDis = 0x1, ///< Disable IOxAPIC/SCI/SMI/NMI interrupt generation
	GpioIntNmi = 0x3, ///< Enable NMI interrupt only
	GpioIntSmi = 0x5, ///< Enable SMI interrupt only
	GpioIntSci = 0x9, ///< Enable SCI interrupt only
	GpioIntApic = 0x11,	///< Enable IOxAPIC interrupt only
	GpioIntLevel = (0x1 << 5), ///< Set interrupt as level triggered
	GpioIntEdge = (0x3 << 5),  ///< Set interrupt as edge triggered (type of
				   ///edge depends on input inversion)
	GpioIntLvlEdgDis = (0x5 << 5), ///< Disable interrupt trigger
	GpioIntBothEdge = (0x7 << 5)   ///< Set interrupt as both edge triggered
} GPIO_INT_CONFIG;

///
/// GPIO Power Configuration
/// GPIO_RESET_CONFIG allows to set GPIO Reset (used to reset the specified
/// Pad Register fields).
///
typedef enum {
	GpioResetDefault = 0x0, ///< Leave value of pad reset unmodified
	GpioResetPwrGood = 0x1, ///< Powergood reset
	GpioResetDeep = 0x3,    ///< Deep GPIO Reset
	GpioResetNormal = 0x5,  ///< GPIO Reset
	GpioResetResume = 0x7 ///< Resume Reset (applicable only for GPD group)
} GPIO_RESET_CONFIG;

///
/// GPIO Electrical Configuration
/// Set GPIO termination and Pad Tolerance (applicable only for some pads)
/// Field from GpioTermDefault to GpioTermNative can be OR'ed with
/// GpioTolerance1v8.
///
typedef enum {
	GpioTermDefault = 0x0,  ///< Leave termination setting unmodified
	GpioTermNone = 0x1,     ///< none
	GpioTermWpd5K = 0x5,    ///< 5kOhm weak pull-down
	GpioTermWpd20K = 0x9,   ///< 20kOhm weak pull-down
	GpioTermWpu1K = 0x13,   ///< 1kOhm weak pull-up
	GpioTermWpu2K = 0x17,   ///< 2kOhm weak pull-up
	GpioTermWpu5K = 0x15,   ///< 5kOhm weak pull-up
	GpioTermWpu20K = 0x19,  ///< 20kOhm weak pull-up
	GpioTermWpu1K2K = 0x1B, ///< 1kOhm & 2kOhm weak pull-up
	GpioTermNative = 0x1F,  ///< Native function controls pads termination
	GpioNoTolerance1v8 = (0x1 << 5), ///< Disable 1.8V pad tolerance
	GpioTolerance1v8 = (0x3 << 5)    ///< Enable 1.8V pad tolerance
} GPIO_ELECTRICAL_CONFIG;

///
/// GPIO LockConfiguration
/// Set GPIO configuration lock and output state lock
/// GpioLockPadConfig and GpioLockOutputState can be OR'ed
///
typedef enum {
	GpioLockDefault = 0x0,    ///< Leave lock setting unmodified
	GpioPadConfigLock = 0x3,  ///< Lock Pad Configuration
	GpioOutputStateLock = 0x5 ///< Lock GPIO pad output value
} GPIO_LOCK_CONFIG;

///
/// Other GPIO Configuration
/// GPIO_OTHER_CONFIG is used for less often settings and for future extensions
/// Supported settings:
///  - RX raw override to '1' - allows to override input value to '1'
///     This setting is applicable only if in input mode (both in GPIO and
///     native usage).
///     The override takes place at the internal pad state directly from buffer
///     and before the RXINV.
///
typedef enum {
	GpioRxRaw1Default = 0x0, ///< Use default input override value
	GpioRxRaw1Dis = 0x1,     ///< Don't override input
	GpioRxRaw1En = 0x3       ///< Override input to '1'
} GPIO_OTHER_CONFIG;

//
// Possible values of Pad Ownership
//
typedef enum {
	GpioPadOwnHost = 0x0,
	GpioPadOwnCsme = 0x1,
	GpioPadOwnIsh = 0x2,
} GPIO_PAD_OWN;

typedef uint32_t GPIO_PAD;

struct dnv_pad_config {
	GPIO_PAD GpioPad;
	struct GPIO_CONFIG GpioConfig;
};

/* Configure GPIOs with mainboard provided settings */
void gpio_configure_dnv_pads(const struct dnv_pad_config *gpio, size_t num);

#endif /* __ACPI__ */
#endif /* _DENVERTON_NS_GPIO_H_ */